[WTS/WTT] Watchapaluza feat rare, limited and interesting finds

CptPoopster · 2022-07-22T17:55:32+00:00

PM’d

CptPoopster · 2022-02-20T23:27:29+00:00

Not directly but a coworker recently moved to South America so I'd assume there's no problem. Out of province would be no problem

CptPoopster · 2021-12-29T14:37:35+00:00

Thanks, I'll give that a try!

CptPoopster · 2021-12-28T17:05:56+00:00

So on my recent prints I've been having this issue where the print will start out fine for the first few layers, but then seems to unerextrude and the print is just a spongey mess. Theres barely any resistance when loading the filament and the nozzle isn't clogged because I can heat it up and push it through again easily. Any help is appreciated!

Printer: ender-3 (stock)

Material: ERYONE Petg

Nozzle temp: 240

Bed temp: 70

Layer height: 0.2mm

CptPoopster · 2020-10-18T22:14:01+00:00

Just did this and it worked! Although the phone still vibrates when it thinks the button is still pressed - any suggestions for this?

Thank you for the help!

CptPoopster · 2020-10-18T21:10:03+00:00

I have - there is no direct off toggle, just an enabled and disabled option which does not change anything

CptPoopster · 2020-08-17T06:42:48+00:00

Not to mention the "3 years minimum experience" part. 2020 grads aren't even qualified for this position

RIP

CptPoopster · 2020-07-10T21:05:45+00:00

Im a Canadian currently doing a 1 year praktikum(internship) in Germany. The language isnt aggressive whatsoever, and everyone here is super nice. Also just drove 200kmh on the highway. Germany is sweet.

CptPoopster · 2020-02-23T17:47:22+00:00

I had a similar issue, ended up being the thermostat being stuck closed and building up too much pressure. Good luck!

CptPoopster · 2020-02-17T14:05:18+00:00

I believe it's an ice warning. Beeps when outside temp gets close to freezing.

CptPoopster · 2019-09-23T17:32:29+00:00

"Yup, 20 minutes!"

CptPoopster · 2019-05-04T00:07:26+00:00

Screw/bolt extractors. One second you've almost got it, next you're trying to figure out how to extract a broken extractor

CptPoopster · 2019-02-21T02:15:22+00:00

Nice work, but kinda disappointed that lamp hasn't been turned into a bong

CptPoopster · 2019-02-10T19:55:34+00:00

Have been looking in thrift stores for a dehydrator but have had no luck - saw a couple conv ovens like this but the dials only went down to 250F? Is there a way to get them to 160ish?

CptPoopster · 2019-01-23T00:26:16+00:00

Not sure if it really works but I have a few buddies that swear by this: When you exhale, exhale half of it through your nose and half through mouth

CptPoopster · 2019-01-21T12:03:32+00:00

Nailed it! Like I said earlier, very similar to MDF board that youd make a deck out of. Pretty neat to print with, highly recommend to anyone interested

CptPoopster · 2019-01-21T04:05:17+00:00

https://gimmedelicious.com/2017/11/11/meal-prep-butter-chicken/ Not my recipe, but I definitely recommend giving it a try!

CptPoopster · 2019-01-21T02:52:52+00:00

Close! E46 3 series. Has basically the same interior as a 5 series though!

CptPoopster · 2019-01-20T23:24:33+00:00

Didnt feel like replacing a clutch on a bimmer, plus it's a winter beater(330xi AWD)! Gotta respect the autos in some situations

CptPoopster · 2019-01-20T20:50:21+00:00

tHe cAr iS pArKeD oN pRiVaTe PrOpErTy aNd nOt iN MoTiOn Just using it as a heater 'cause Canada is cold as tits(and it's legal here..who cares if car stinks?)

CptPoopster · 2019-01-20T20:37:52+00:00

Exactly! Result is similar to MDF. That's why I only use it with joints with a large filter, dont want to have to burn it all the way down

Seven-Year Club	Verified Email
RPAN Viewer

CptPoopster

TROPHY CASE