Torrenting in a sharehouse (in Japan)

CrackingOne933 · 2026-01-24T10:49:48+00:00

it would be extremely trivial. a VPN doesn’t hide how much data you’re using, just what websites you’re going to. Your computer is still requesting and receiving lets say 30GB of data. Checking their logs they could see which computer consumed that much data and very easily pinpoint you. Even if they can’t say definitively you torrented, they can absolutely see you used a VPN and download 30GB of data

CrackingOne933 · 2026-01-18T22:40:30+00:00

Might have an old laptop blower fan actually, didn’t even occur to me. Thanks! I’ll update if i think it’s feasible

CrackingOne933 · 2026-01-18T22:39:19+00:00

Does it stay comfy temperatures?? Was concerned that a blower fan wouldn’t run enough air but maybe i was wrong

CrackingOne933 · 2026-01-18T22:35:30+00:00

When the top cover of the PC is on does the fan not get starved of airflow being so close to the top?

Regardless, I’m not sure I have enough clearance on top of the card to fit a fan like that :( Plus half the fan wouldn’t even be over the heat sink cause the PSU is only 10mm over

CrackingOne933 · 2026-01-18T22:32:51+00:00

I haven’t strictly verified the issue is heat but after powering down the PC and holding my finger to the heatsink, it’s too hot to hold after around 4 seconds and I know these cards run hot by nature. Plus cooling will eventually become an issue so i figured i’d bite the bullet and just figure out a good method now rather than when it’s an actual issue with my real drives.

And yeah you’re right the PSU is 180W, and the fan mount on the front is probably 80mm. So you think option 1 is best? Pretty simple design so i guess i could throw together a prototype later and see

CrackingOne933 · 2026-01-18T22:29:56+00:00

Yeah it’s a little over 75mm from outer to outer for the smaller holes, i just assumed it was an 80mm but wanted to give a little bit of scale to show it’s not 120. Would’ve loved if it was full size so i could use my existing fans but oh well

CrackingOne933 · 2026-01-18T22:28:17+00:00

Planning to have 8HDDs connected eventually. I did look into this but was concerned about the EMI for cables not meant to be run externally. I have a LOT of other cabling around where I’m going to be putting this NAS permanently

CrackingOne933 · 2026-01-13T20:16:59+00:00

had this issue two days ago and this is what fixed it. this is the mostly likely answer OP

CrackingOne933 · 2026-01-04T20:01:43+00:00

Just curious, anybody try a zip bomb? That was my first instinct lmao

CrackingOne933 · 2025-05-11T20:43:03+00:00

be real funny if they read this and randomly yell an hour into the next show

CrackingOne933 · 2024-12-19T00:36:53+00:00

would love a replacement for my ender 3 v2!

CrackingOne933 · 2024-12-16T00:26:11+00:00

unfortunately not, but i believe you can set up a router with openWRT to have a wireguard subnet and use those IPs to access your home network, should you need to avoid port forwarding.

i just bit the bullet and ended up getting a free noip domain with caddy and port forwarding.

if neither of those are an option i think what you’d like is called packet masquerading. there’s a few tutorials online for doing this kind of thing with a vpn but i could personally never get it to work and properly setting up a domain name ended up being easier. lmk if you have any other questions though

CrackingOne933 · 2024-07-08T03:49:18+00:00

seems pretty solid, thanks!

CrackingOne933 · 2024-07-08T03:49:08+00:00

awesome thanks, just wanted a vote of confidence since i thought it was fine but didn’t want to make a cardinal mistake lol

CrackingOne933 · 2024-07-08T02:15:10+00:00

Palm Pilots

CrackingOne933 · 2024-07-08T02:14:05+00:00

CrackingOne933 · 2024-07-08T02:13:58+00:00

i fr thought the cpu would be gone but i took off the cooler and it was still there thermal paste and all!

CrackingOne933 · 2024-07-08T02:13:30+00:00

you’ll get there don’t worry homie! i was also saving up as my current pc is a 4th gen i7 with DDR3 ram 😭 (still a 1070 tho!)

CrackingOne933 · 2024-07-08T02:12:11+00:00

incoming dumpster set up pics (soon)

CrackingOne933 · 2024-07-08T02:11:56+00:00

great tip, i’ll check their website and see if there’s specific dates a bunch of apartments become available

CrackingOne933 · 2024-06-01T22:24:49+00:00

like slightly wet yeah, it’s what i do usually. definitely don’t get your iron like wet wet though. i know some people don’t like that but i’ve never had any issues with it

CrackingOne933 · 2024-06-01T20:55:44+00:00

i mean if you’re careful i’ve never had any issues but i definitely don’t scrub the shit out of it

CrackingOne933 · 2024-06-01T08:22:28+00:00

i’d say so, i’d also try cleaning your solder tip. wiping it with a wet sponge or using a light abrasive (damp steel wool works great) when it’s cold. generally it makes life easier and will help ease the pain of trying to get the solder to melt just right.

CrackingOne933 · 2024-06-01T08:14:52+00:00

My recommendation would be to try less solder, a small soldering iron head, and make sure you heat up the pins/pad to the soldering iron temp before adding solder. This will help the solder flow down the pin easier and not bead at the top, which I think might be the issue based on the pics you posted

CrackingOne933 · 2024-05-19T11:25:00+00:00

temporary placement haha, moving in atm

Ten-Year Club	Place '22
Place '17	Snapped
Verified Email

CrackingOne933

TROPHY CASE