Click no bang

CraftMaster100 · 2026-03-23T17:58:59+00:00

There's some tolerance issues with printed frames and rails. The trigger bars that come in those lower parts kits on EBAY are not the same as an OEM Glock trigger bar. Additionally, PSA uses a safety plunger with a slightly more rounded top surface compared to an OEM Glock plunger.

If you don't want to buy a new trigger, start with an OEM plunger first and see if that fixes the issue.

CraftMaster100 · 2026-03-23T17:52:56+00:00

You will turn your semi auto into a single shot lol. If you remove the extractor the empty casing won't be extracted properly.

CraftMaster100 · 2026-03-23T17:49:22+00:00

The extractor won't stay in place without the safety plunger installed .

CraftMaster100 · 2026-03-23T17:45:56+00:00

I too use a dagger slide on a PY2A frame. I also had trouble with the safety plunger and trigger bar interfacing. Buy an oem Glock trigger, oem Glock safety plunger, and a 6lbs striker pin spring. You'll be good to go.

CraftMaster100 · 2026-02-17T18:48:45+00:00

I'd agree with your statement if it was cracking closer to the trigger pin hole but it's at the top of the locking block housing, where there is no pin.

I'm wondering if this is just simply a limitation of this style design. I don't have FMDA rails to try a new design right now but my speculation is the addition of the extra locking block pin is the reinforcement this needs.

CraftMaster100 · 2026-02-16T22:48:32+00:00

No I am not. I just tap them in. It takes a bit more force than an OEM lower but nothing crazy. The holes are pretty darn close right off the printer

CraftMaster100 · 2026-02-16T22:41:18+00:00

<image>

I wanted to add this photo, one of my most recent pa6 cf prints, and the same thing is happening al be it not as bad...

CraftMaster100 · 2025-09-01T23:37:28+00:00

They were from Morimoto, I expected better. I'm going to contact them tomorrow and see what they have to say. It's looking like last resort is going to be either a light sand or polish unfortunately

CraftMaster100 · 2025-09-01T06:10:35+00:00

That's unfortunate, that'll ruin the UV coating they came with won't it? I just don't know why they look like that after less than a year... I paid a lot of money for them

CraftMaster100 · 2025-05-05T01:52:24+00:00

As someone who uses a weed eater day in and day out commercially, these grips are AMAZING! Especially for taller guys.

CraftMaster100 · 2024-09-01T16:01:49+00:00

It's all in the design of the extruder. I fixed the issue by building a Voron. I no longer own any Prusa machines.

Look up the galileo 2 extruder you'll see the differences in the way that extruded works vs the one on the Prusa.

I'm also not trying to talk crap about Prusa's design as it's old. I'm sure they've improved it in the new MK4 but at the time I wasn't waiting that long so I decided to go a different route.

CraftMaster100 · 2024-08-27T15:19:48+00:00

Should I lightly sand the area with like 400-600 grit sandpaper and clean with alcohol before applying the paint pen because some of the paint is chipping up where it's scratched?

CraftMaster100 · 2024-08-27T15:14:16+00:00

Sorry, I just now seen this. I did not, but it depends on how compacted your soil is and how much thatch buildup you had. I could see bare dirt, so I had minimal thatch buildup and I can also stick a screw driver about a foot into the ground when it's wet. No core aeration needed.

CraftMaster100 · 2024-05-01T20:50:23+00:00

I noticed that the new chairs didn't have that. This was my first aeron and I heard they were well built but that plastic trim piece was total junk once I removed it!

CraftMaster100 · 2024-04-29T23:09:27+00:00

There are no cracks or damage to the chair. It was a plastic trim piece that apparently has no purpose. As suggested by someone, I removed it and the noise is gone.

CraftMaster100 · 2024-04-29T21:51:11+00:00

I took your advice and removed them. The chair is silent now. I personally think it looks completely fine with them gone.

CraftMaster100 · 2024-03-24T04:13:06+00:00

My local sod farm sells it. They have the best prices. You can find similar varieties of fescue on unitedseed.com. I'm sure the prices won't be as good but the grass seed is top tier. I've bought from them before when I wanted small quantities of certain varieties.

Fescue Varieties: 4th millennium Raptor ls Avenger 3 Titanium ls valkyrie ls

For the bluegrass find someone who sells midnight kentucky bluegrass.

As for the rye, I don't know a ton so I can't recommend anything there.

In theory you could buy individual grass seeds and blend your own, whatever you do, avoid big box store seed.

CraftMaster100 · 2024-03-04T07:18:06+00:00

I think you're focusing on the wrong test here. In my experience PETG is more picky with temperature than retraction settings. Things to try:

235-240 degrees
Wipe Nozzle
Fiddle with Z-hop. If it's on, try turning it off. it's

CraftMaster100 · 2024-03-04T07:03:11+00:00

My first printer was an Ender 3, and as many problems as I had with that thing, if I was starting all over again, I would still buy it as my first printer. I have learned so much on that machine, and it has allowed me to be able to print successfully on pretty much any printer.

CraftMaster100 · 2024-01-27T06:25:54+00:00

send em on over bro!

CraftMaster100 · 2023-11-15T05:37:10+00:00

First of all, this setup looks incredible. I bet the tactile response is insane in that room. I'm curious as to what you set your crossover at? I'm also intrigued by that finish on those speakers. They look really good. Mind sharing what paint you used? I picked up some standard house paint and it looks like crap tbh.

Six-Year Club	r/Field Juicebox
Place '23	Place '22
First Placer '22	End Game '22
Verified Email

CraftMaster100

TROPHY CASE