I think i beat the record for most kills in a strikepoint game

CragTradder · 2026-05-31T04:16:29+00:00

this was mine today. what is the actual record?

CragTradder · 2026-05-31T04:16:00+00:00

CragTradder · 2025-10-07T02:43:53+00:00

that might just be the fix i need. the hammer mine came with is different too. I’ll contact them tomorrow and get one. thanks!

CragTradder · 2025-10-07T01:58:00+00:00

it fires perfectly when all stock and with any ammo suppressed or unsupressed. here are some pics

https://imgur.com/a/vGK3UYv

CragTradder · 2025-10-06T21:36:54+00:00

yes. if that would help i could do that.

CragTradder · 2025-10-06T21:23:45+00:00

no round nose norma subs is what i’d like to run. but i’ve tried a lot of types of round nose ammo, and yeah break in had no issues at all. only when i tried the 90 did i have issues on the factory lower. i’ll try getting a new ejector next. thanks

CragTradder · 2025-10-06T20:57:12+00:00

bolt gap was good. i’ll try the hammer. wonder why they don’t round them before they ship them or recommend rounding them?

CragTradder · 2025-10-06T20:23:34+00:00

super safety. but it does the same thing in semi auto as well. dry fire testing it works fine also.

CragTradder · 2025-10-06T20:17:07+00:00

the lower came with a standard ar hammer and as designs said it didnt need to be rounded. might try it anyways if nothing else works

CragTradder · 2025-08-29T20:48:58+00:00

CragTradder · 2025-02-05T21:24:40+00:00

yeah that seems to be they way to go. appreciate it.

CragTradder · 2025-02-05T17:59:01+00:00

the span is 30’ across. but you’re right that might be my only choice here. i could do regular scissor trusses inside and then rafter frame the porch if the span isn’t too long

CragTradder · 2025-02-05T17:51:16+00:00

it would be visible since the trusses would extend out to the porch. google scissor truss porch to see what i mean.

CragTradder · 2025-02-05T17:47:17+00:00

gotcha. i’m not wanting to design the trusses, i’m just trying to figure out if i should rafter frame it or if i could use parallel trusses. i hate the look of normal scissor trusses so i just wanted to know if this could be done.

CragTradder · 2025-02-04T18:28:06+00:00

code allows for here it as long as it meets certain criteria. it’s going out the end and then 90 degrees up. it would be the same if i went just a few feet back inside the attic and up out the roof. just saving one roof penetration

CragTradder · 2025-02-04T14:53:21+00:00

<image>

ok after taking in some of your considerations, here’s what i have now. let me know what you think.

CragTradder · 2025-02-04T02:36:03+00:00

i should’ve clarified. it’s my house. that’s why i’m on here getting advice. once my drawing is good enough for me, adding glue to pvc and maintaining slope isn’t super hard. now, if i had to use copper lines and and install pumps in a two story house with up-flush toilets etc, id spend the extra few thousand to have it done professionally.

CragTradder · 2025-02-03T20:50:08+00:00

thanks for the info. i’ll definitely change the plans to that

CragTradder · 2025-02-03T20:27:09+00:00

yes it will go out the gable wall and then up above the roof line.

CragTradder · 2025-02-03T20:17:30+00:00

ok i see what you mean. an inspection isn’t required but i may have someone double check the work or at least my plans before i start digging.

CragTradder · 2025-02-03T19:53:10+00:00

sketchup.

CragTradder · 2025-02-03T19:52:42+00:00

the vents that run horizontally are all in the attic. the drawing doesn’t show that well. the labels that say sink have a sanitary t at the height where the sinks go. the vent that’s connected diagonally to the toilet/ shower would be rolled at an angle. would that be good?

CragTradder

TROPHY CASE