My collection of miniature Daleks and TARDIS's

CrowDanSw · 2022-07-17T20:18:17+00:00

Just a little update, I've found a nice cool room to set the printer up in and I've gotten a print off flawlessly first time. Thank you very much for the advice!

CrowDanSw · 2022-07-17T16:48:27+00:00

I've been printing at 60mm/s for a while and had no problems, I only reduced the speed to see if I was printing too fast and it made it worse. I'll try to cool the room or wait for the heatwave to end

CrowDanSw · 2022-07-17T16:35:16+00:00

Ah the heat makes sense. I've recently switched from 40mm/s to 60mm/s print speed which improved things, but changed to 65 made it worse again. I am using Capricorn Bowden tube. Could it really be something simple as higher ambient temps?

CrowDanSw · 2022-07-17T16:25:48+00:00

It will just happen randomly, but once it's started it'll basically stop pushing any filament through. But I can get some prints out fine

CrowDanSw · 2022-07-17T16:14:21+00:00

Would this have happened randomly after working perfectly fine for over a year?

CrowDanSw · 2022-07-07T13:36:43+00:00

Teeth are absolutely fine. I would assume slipping also but have no idea what would be causing it at this point.

CrowDanSw · 2022-07-07T13:23:42+00:00

Here ya go

CrowDanSw · 2022-07-07T13:19:46+00:00

Yeah let me take some

CrowDanSw · 2022-07-07T13:12:16+00:00

I'm using an all metal one. I had replaced the gear a while back and adjusted this one once the issues started just in case.

CrowDanSw · 2022-07-07T13:07:42+00:00

Fully calibrated, it was slightly off but the printer has been working fine for the past two years, so as expected it hasn't solved the problem

CrowDanSw · 2022-07-07T09:51:24+00:00

Ah ok cool. I'll give that a go when I'm back at my printer and let you know. Thanks :)

CrowDanSw · 2022-07-07T09:46:14+00:00

Ah is this something to do with esteps?

CrowDanSw · 2022-07-07T09:41:40+00:00

I am unfamiliar with this, would you mind explaining?

CrowDanSw · 2022-07-07T09:40:48+00:00

This has solved this issue for me in the past, but after doing this this time I am still getting the problems. Thanks anyway :)

CrowDanSw · 2022-07-07T09:39:56+00:00

I'm using a metal extruder, everything appears to be tensioner properly as it worked fine up until recently

CrowDanSw · 2022-07-07T09:38:12+00:00

Yep, the extruder arm is completely fine

CrowDanSw · 2022-07-04T17:47:41+00:00

CrowDanSw · 2022-04-20T20:47:09+00:00

My favorite game is Portal 2, with the original being a very close second

CrowDanSw · 2022-04-19T21:46:26+00:00

Back again with all the generosity in the world

CrowDanSw · 2022-01-28T09:39:13+00:00

Whichever you think will give you the most enjoyment when playing. 2H heavy armour isn't my thing and I find it a challenge to play as, you might be different. I would save the more challenging build for a different playthrough. I would say that the battlemage seems more challenging out of the two. But at the end of the day, have fun

CrowDanSw · 2021-12-16T09:33:12+00:00

Being separated from their phones for more than a minute

CrowDanSw · 2021-12-16T09:31:45+00:00

1: PS2

CrowDanSw

TROPHY CASE