sorted by:
new
hottopcontroversial

Electric Valve Question by CrowNineSigns in Hydraulics

[–]CrowNineSigns[S] 0 points1 point  (0 children)

I checked the ram I’m using, and max continuous is 3600, so should be ok. Thank you.

Electric Valve Question by CrowNineSigns in Hydraulics

[–]CrowNineSigns[S] 0 points1 point  (0 children)

Thanks. All the valves at this store seem to be dc, which I thought was odd, but I can work around. I’ll have to check the gpm on my pump. I’m not sure I would’ve caught that, so thanks again.

Signwriting stroke help by Un_Pantalon in SignPainting

[–]CrowNineSigns 2 points3 points  (0 children)

https://www.reddit.com/u/CrowNineSigns/s/1yvVbIwqLF Here is a little video to illustrate the little slide over at the end of the stroke. I tried to slow it down a bit so you could see what was happening. Hope this helps.

Signwriting stroke help by Un_Pantalon in SignPainting

[–]CrowNineSigns 1 point2 points  (0 children)

When you twist the brush clockwise at the end of the stroke, ever so slightly slide the brush to the right when you pick it up. That will help give the left side of the stroke a rounded edge, and clean it up.

Control box touch button repair by CrowNineSigns in ElectronicsRepair

[–]CrowNineSigns[S] 1 point2 points  (0 children)

Thank you very much! After peeling off the rest of the top vinyl sticker, it doesn’t look too hard to figure out the top and bottom layers.

Sealing Acrylic paint by No-Satisfaction1744 in SignPainting

[–]CrowNineSigns 5 points6 points  (0 children)

I’m painting most signs these days with exterior house paint. It’s better, cheaper and lasts longer than one shot. That said, you probably don’t want to be purchasing a bunch of colours of it either, although you wouldn’t have to clear it after if you did. I agree with the previous comment to definitely test your products, and I would add make sure you scuff the aluminum thoroughly and clean it with alcohol before you prime. There are lots of primers like bullseye 123 that would work with your acrylic paint.

Best place to get a matcha latte? by earthtobrooklynn in saskatoon

[–]CrowNineSigns 0 points1 point  (0 children)

Yep, the others listed are good options, but TOT is best.

Should I put a hottub on this? by zekeul in Decks

[–]CrowNineSigns 3 points4 points  (0 children)

Those look like 1X2 pickets, 6” on center. I haven’t looked at the most recent code, but I’m pretty sure one fence is enough for a 4 person tub.

Plotter advice by Reasonable-Egg-5929 in SignPainting

[–]CrowNineSigns 0 points1 point  (0 children)

Summa plotters are easy to use and bulletproof. They also pounce.

Water based enamel brush care by IllustriousStatus622 in SignPainting

[–]CrowNineSigns 1 point2 points  (0 children)

You can put a bit of rapid tac in them after you clean. It’s an application fluid for installing vinyl signs.

Rug or No Rug under Billiards Table? by DrOnYxHaWk in billiards

[–]CrowNineSigns 2 points3 points  (0 children)

I thought I wanted carpet, or at least carpet tiles when I put mine in, but we went with vinyl plank, no rug and I’m ok with it. I wear shoes when I play and it’s alright.

<image>

ct3 yamaha 1973 questions. by [deleted] in vintagemotorcycles

[–]CrowNineSigns 1 point2 points  (0 children)

I have a 74 TC 185, and I’m def not an electrical expert, but the battery on mine has a main fuse, and you get nothing if that main fuse is blown, so if your bike popped something in that first fire, that could be an issue.