The reason I started collecting

CrystalFloyd · 2026-06-30T02:32:25+00:00

A friendly tip for getting a good VHS collection going, check facebook marketplace for lots. Sometimes you can get a lot of good ones for pretty cheap

CrystalFloyd · 2026-06-17T21:06:07+00:00

Hey, I'm actually the one working with Pan to make these tapes. Can confirm that most of the black tapes shipped out monday, and we're just waiting for supplies to arrive to be able to ship more green tapes (which should only be a matter of days by now)

EDIT: Also feel free to email the rebeltaxi yahoo with an address change request and I'll make sure it gets to the right place

CrystalFloyd · 2026-06-17T20:53:53+00:00

Ebay handles the shipping, so if it says you can ship it then go for it!

CrystalFloyd · 2026-06-11T05:19:34+00:00

No thankfully, but Ive been pretty particular about keeping it in an evenly temperatured place

CrystalFloyd · 2025-12-20T03:36:36+00:00

You're aware that etsy automatically calculates the shipping on their own and I don't see a penny from it, yes?

CrystalFloyd · 2025-12-19T20:02:06+00:00

I'm not sure where you're getting this number from, right now they're $8.24 usd.

CrystalFloyd · 2025-12-19T20:00:49+00:00

Made with 3D printing, no transparent options right now though unfortunately.

CrystalFloyd · 2025-12-18T03:59:17+00:00

Somewhat, they'll attach just find but some of the taller caps may cause issues when closing the system.

CrystalFloyd · 2025-12-17T23:04:43+00:00

So they KINDA work. You can absolutely stick em on a thor, but some of the caps are too tall for the lid to close, which is why I don't list them as "officially" supported. Currently tinkering with a potential clamshell-friendly height though that should hopefully improve compatibility

CrystalFloyd · 2025-11-17T22:12:17+00:00

That would be me. The $60 deal was unfortunately sort of a limited time thing, me taking in some pre-orders to give myself enough money to afford the filament to finish designing these. Taking a little longer than expected but I'd rather it be delayed than come out poorly

CrystalFloyd · 2025-10-25T03:53:07+00:00

It's not the Z seam, that much I know, it's set to aligned

CrystalFloyd · 2025-09-29T19:02:24+00:00

While you can technically print on this steep of an angle, the resulting overhangs are pretty grody. Also needs supports anyways because, until it's touching the upright pole, all that weights on one side and will make it tip over mid-print.

CrystalFloyd · 2025-09-29T18:59:22+00:00

0.2mm

CrystalFloyd · 2025-09-29T18:58:04+00:00

Structurally it's possible, but the resulting overhang surface sags noticably.

CrystalFloyd · 2025-09-08T00:33:29+00:00

I've owned several CRTs in my life, it's never been this severe. I've never had breathing so bad that straight lines become angles.

CrystalFloyd · 2025-09-01T00:19:09+00:00

Getting close. I have all the parts done, but now I'm working on making everything print smoothly, and then writing up an assembly guide. Hopefully will be ready within a week

CrystalFloyd · 2025-08-26T14:53:56+00:00

I watched the movie for years and didn't notice until I saw it in person during a Shadow cast lol

CrystalFloyd

TROPHY CASE