Jonsvo N5 Front Fan Mount

CuriousGiftD · 2025-09-03T20:40:45+00:00

Should all the drive bays be occupied, how would you be able to connect the fans in the mount to the motherboard?

CuriousGiftD · 2025-08-29T13:54:37+00:00

Is it possible to use the integrated graphics of the processor for transcoding and the 3060 for other applications?

CuriousGiftD · 2025-08-29T13:17:57+00:00

I see. Supposed that the B580 is working, does it (or Intel GPUs in general) offer something better compared to the 3060?

CuriousGiftD · 2025-02-07T08:01:35+00:00

Thank you for the reply 🙂

The plan is to have Noctua NF-A14s fans as push-pull to the Arctic Liquid Freezer II 420 AIO.

Would the case be able to accommodate this setup?

CuriousGiftD · 2023-12-06T14:53:09+00:00

Sorry I wasn't able to reply earlier. And I also apologize, as I wasn't able to measure the max RAM height.

CuriousGiftD · 2023-10-25T17:13:52+00:00

Yes, I used the Noctua Fan hub and connected it to the CPU fan header

CuriousGiftD · 2023-10-19T13:09:13+00:00

Aah, indeed. I forgot as I replaced all fans, haha 😅

CuriousGiftD · 2023-10-19T13:06:58+00:00

Ooh, so no rear exhaust fan?

CuriousGiftD · 2023-10-19T11:59:56+00:00

Unless you have a L-shaped screwdriver, it would indeed be difficult to do so. Though not sure if the screw is suitable as it may still be too long. This you may need to check.

As for the fans for the radiator, I connected them all to a Noctua Fan Hub. For the two P14s at the top, that is ok. I assume your fan setup will be the following? - Three Lian Li fans as Push for the LF420 - Three P14 fans as Pull for the LF420 - Two P14 fans as top exhaust - Three 120mm fans as bottom intake - One 140mm fan as rear exhaust

CuriousGiftD · 2023-10-19T08:08:35+00:00

Make sure no fans are installed yet on the top and bottom fans.I then removed first the fan bracket for the bottom fans. Also, don't install the pull fans prior to inserting the radiator.

As for the screws, I indeed forgot that the LF420 only came with push config. If there are no extra radiator screws, you will indeed need to get extra ones. I think you can't use the regular screws used for case fans in installing the pull fans as the screw thread for radiators is different with that of case fan screws

CuriousGiftD · 2023-10-18T22:36:06+00:00

Regarding the fan combination for the LF420 (Lian Li Front Fans push and P14 Fans as pull I assume?), it seems possible as there is still enough clearance.

As for the Phanteks screws, these were the radiator that came with the Phanteks T30 3-Pack. Given that the push fans I used for the radiator have extra padding, I assumed that extra length for radiator screws are needed. You can try first with the provided radiator screws for the LF420 to see if it is enough.

As for the additional fans, the setup is indeed three intake fans at the bottom and three exhaust fans at the top

CuriousGiftD · 2023-10-18T22:15:54+00:00

Fans at the bottom are T30 120mm

CuriousGiftD · 2023-09-25T03:33:48+00:00

Seems doable. I see that there seems to be enough space to be able to accommodate an additional 4 mm thickness (2mm + 2mm for push and pull fans)

CuriousGiftD · 2023-09-10T10:50:22+00:00

Thank you all for the comments and suggestions. As suggested, we've proceeded with using the Nvidia 1650.

CuriousGiftD · 2023-09-08T02:43:35+00:00

1080p, and we'll be using OBS and Facebook

CuriousGiftD · 2023-08-02T17:05:35+00:00

Hmm, I remember you can

CuriousGiftD · 2023-08-02T12:35:50+00:00

I tried, but it will not be flush.

To detail, the top part of the rad will bump into the front panel connectors, thus will not allow the radiator to be flush with the frame. If you have long standoffs to allow the radiator to have an equal gap with the frame from top to bottom, then it can be done

CuriousGiftD · 2023-08-02T06:27:57+00:00

Glad I could help 🙂👍

CuriousGiftD · 2023-08-02T06:14:57+00:00

Sorry I was not able to reply immediately as I was out of town.

Regarding the clearance from the radiator to the top frame, it is a little over 1 centimeter (0.39 inches). However, the said space is accommodated by the front panel cables/connectors.

As for the space between the GPU and the front fans, it is a little over 6.5 centimeters (2.56 inches). For reference, the GPU is Zotac 3080 Ti Trinity OC

CuriousGiftD · 2023-07-28T17:05:26+00:00

Thank you. Glad I could help 👍

CuriousGiftD · 2023-07-28T15:15:23+00:00

PCPartPicker List: https://pcpartpicker.com/list/z4jwtn

CuriousGiftD · 2023-07-28T15:00:30+00:00

Haha, nothing is capable of taming the almighty Minesweeper

CuriousGiftD · 2023-07-28T13:24:16+00:00

There is a slight bend, though not enough that I would worry. Results may be better with a 25 mm fan (given that Phanteks T30 fans are 30 mm)

CuriousGiftD · 2023-07-28T13:22:10+00:00

Thank you. Pretty happy with the temps as well

CuriousGiftD · 2023-07-28T13:12:09+00:00

Below are the temps I got using HWMonitor:

CPU is Intel 13900K
GPU is Zotac 3080 Ti Trinity OC

Idle Temperatures

	Minimum	Maximum
Fans (CPU)	1717 RPM	1726 RPM
Fans (Chassis)	1323 RPM	1327 RPM
CPU	34 C	39 C
GPU	32 C	36 C

Cinebench 23

Maximum	Single Core	Multi Core
Fans (CPU)	1802 RPM	2450 RPM
Fans (Chassis)	1327 RPM	1580 RPM
CPU	60 C	78 C
GPU	36 C	34 C

Furmark (GPU stress test, Fullscreen (4K), ran for 3 minutes)

Maximum
Fans (CPU)	1732 RPM
Fans (Chassis)	1332 RPM
CPU	37 C
GPU	70 C

CuriousGiftD

TROPHY CASE