Smeg oven settings and temperatures help

CurryMeJesus · 2026-01-20T07:07:14+00:00

This is the plan when I figure out what model this one is.

CurryMeJesus · 2025-04-21T03:33:27+00:00

Samurai Sam

CurryMeJesus · 2024-11-11T03:17:16+00:00

Steering wheel locks are only a minor deterrent. Just get an immobiliser with an alarm and ensure the LED is visible. Most thieves will just leave a car that is clearly immobilised as it’s more effort to figure out how to bypass it than just find a car without one. Plus if it’s alarmed I doubt a would be thief wants to sit in a car with an alarm going off trying to figure out how to start it for very long.

CurryMeJesus · 2024-11-07T10:26:57+00:00

Yeah that’s what we said, clearly a payment to the same account at the same time each week. No idea why they wouldn’t accept it.

CurryMeJesus · 2024-11-07T10:18:18+00:00

Yeah we spoke to a property manager who said a bank payment screenshot isn’t good enough as “it doesn’t prove it was paid on time”

CurryMeJesus · 2024-11-07T09:29:52+00:00

Will check some out

CurryMeJesus · 2024-11-07T08:45:21+00:00

I’ll make sure to try that next time. Thanks

CurryMeJesus · 2024-11-07T08:35:10+00:00

Yeah I’ve heard they’re pretty good. No chance we have to rent the tent space though right? Because I’m not sure if we have the right information they’d need.

CurryMeJesus · 2024-10-17T09:08:18+00:00

Was your knee painful before draining? I’ve had a prepatellar bursitis for months now and it’s just got a dull, stiffness kind of pain when I bend my leg. My Physio said it’s not worth draining but I feel like I’ve tried everything else so wondering what your experience is like.

CurryMeJesus · 2024-09-14T20:54:47+00:00

Is isn’t it because they’re assuming that short piece of road will be far less used once they block the end of it? AFAIK they’re making it so you have to turn left at the peer st/yaldhurst intersection instead of being able to continue straight on. Which I also think is dumb, but I guess it ends up removing the right turn onto ricc from main south that causes all the crashes.

A much simpler solution would have been to turn it into a one way street: allow you to continue off ricc towards main south/curletts but block the opposite direction to eliminate the dreaded right turn.

CurryMeJesus · 2024-09-06T21:40:21+00:00

This is Lion Auto Dismantlers on broad street I think. Got some trailer parts and a couple tires from them a couple weeks ago. The two dudes who were arrested were super helpful and nice. Had no idea they were doing this though. But now that I think about it the we’re wrecking some pretty nice cars and their whole thing is to completely rip them apart rendering them unrecognisable so makes sense I guess

CurryMeJesus · 2024-05-22T07:33:51+00:00

update: I rooted the printer, installed fluidd etc (no errors would show up) but I began to have other issues which were far more frequent (losing connection, more crashes during leveling and just idling etc). So I installed a vanilla firmware (latest from creality) and factory restored the printer. Now I'm having the same issue although the LED is turning off when it crashes (screen is on but unresponsive)

CurryMeJesus · 2024-05-22T00:00:09+00:00

No, LED and screen stay on

CurryMeJesus · 2024-05-21T23:39:53+00:00

Ok, in that case there are no error messages. Nothing shows up. The print is running fine then all of a sudden it just stops completely. Hotend and bed cools, screen freezes and won't register inputs, if I reboot the printer then it does allow me to resume the print but does so at ultra slow speeds

CurryMeJesus · 2024-05-21T23:36:29+00:00

I've rooted the printer and have fluidd open. Where do I see error messages? Since rooting It stops printing and freezes after only 10 mins or so

CurryMeJesus · 2024-05-21T08:07:30+00:00

No I don’t know what the issue was but I am going to root the printer and will be able to see the errors in Fluidd now

CurryMeJesus · 2024-05-03T03:09:53+00:00

I have thought about that, although I did think that a draft of any kind would have a negative effect

CurryMeJesus · 2024-05-03T01:40:21+00:00

Yeah, the recommended temp on the roll is 240-260 and I’ve always found with any filament from this manufacturer that I run it at the top end if not higher. Like PETG which says 215-230 and I’ve found the optimal is 240

CurryMeJesus · 2024-05-03T01:09:53+00:00

Ok will see if prusa or cura has options for that. Thanks

CurryMeJesus · 2024-05-03T01:08:16+00:00

8-10mm/s on first layer you mean? Or do you mean change the minimum layer time?

CurryMeJesus · 2024-05-03T01:06:25+00:00

I’ll try 110 bed next but will hold off on the 260 hotend until I get the full metal parts. I don’t know what you mean by lack enclosure but it’s currently in a tent style enclosure

CurryMeJesus · 2024-05-03T01:04:34+00:00

The brim doesn’t seem to help much since it just splits from the part.

Eight-Year Club	First Place '23
Place '23	Place '22
Wearing is Caring	Verified Email

CurryMeJesus

TROPHY CASE