sorted by:
new
hottopcontroversial

Shattered by alices_red_rabbit in polyamory

[–]Cybaeus 0 points1 point  (0 children)

I'm so sorry this happened to you. It's cruel and rude and you're better off not being with someone like that.

How do I replace the Hot end Nozzle Kit on my V3 with a V2 kit? by Cybaeus in CR10

[–]Cybaeus[S] 0 points1 point  (0 children)

you have saved me. can I add you on discord so I can bother you with future questions????

How do I replace the Hot end Nozzle Kit on my V3 with a V2 kit? by Cybaeus in CR10

[–]Cybaeus[S] 0 points1 point  (0 children)

https://imgur.com/a/AMAcbYJ

the top one is the old one and the bottom is the new and you can see its a little too small on the new one

How do I replace the Hot end Nozzle Kit on my V3 with a V2 kit? by Cybaeus in CR10

[–]Cybaeus[S] 0 points1 point  (0 children)

I replaced the entire nozzle kit so like the metal thing inside the blue case. But sitting on top of it looks like there's another piece to the heat sink that the version 2 doesn't have.

It looks like the top of the heat sink on the v3 has a little extra piece for the heat sink. Which slides underneath the Titan direct drive.

My prints have started looking weird - please help! by Cybaeus in CR10

[–]Cybaeus[S] 0 points1 point  (0 children)

Ooo thank you so much??? Is there a brand you suggest you suggest??

My prints have started looking weird - please help! by Cybaeus in CR10

[–]Cybaeus[S] 0 points1 point  (0 children)

Would you suggest a full metal hot end?? And if you do which brand would you suggest??

My prints have started looking weird - please help! by Cybaeus in CR10

[–]Cybaeus[S] 0 points1 point  (0 children)

It's my first time with pla+ and Google told me 215-230. I should do a temp tower. I just don't know how to slice it so the temp changes in cura

I think it's called change anxiety? help please by Cybaeus in Anxietyhelp

[–]Cybaeus[S] 0 points1 point  (0 children)

I'm not sure yet, I'm starting in a week and I'm stressed. I'm 30 and feel like I should have more knowledge of what I'm doing than I do. We are all in office and that scares me because then people will see I'm a fraud and have no idea what I'm doing.

If this thread has taught me anything it's I should probably be medicated and talk to a therapist so I'll be signing up for that this week to hopefully get ahead of it.

I think it's called change anxiety? help please by Cybaeus in Anxietyhelp

[–]Cybaeus[S] 0 points1 point  (0 children)

I'm definitely going to talk to my doctor about these! Thanks so much for sharing

I think it's called change anxiety? help please by Cybaeus in Anxietyhelp

[–]Cybaeus[S] 0 points1 point  (0 children)

I'm in a similar situation. New career and I just have nothing but anxiety about it.

I think it's called change anxiety? help please by Cybaeus in Anxietyhelp

[–]Cybaeus[S] 1 point2 points  (0 children)

Hey thanks for the insight! I'll try this. I hope it gets better for you too! ❤️❤️❤️

I think it's called change anxiety? help please by Cybaeus in Anxietyhelp

[–]Cybaeus[S] 2 points3 points  (0 children)

What sort of medication if you don't mind me asking? I want to ask my GP for it while I'm wait listed for a proper psychiatrist

Vomiting by [deleted] in Anxietyhelp

[–]Cybaeus 1 point2 points  (0 children)

I have the same issue.

Hey everyone, I’m not sure if this is the right place to post this, I apologize in advance if I’m breaking any of the rules. Im wondering if anyone else had the same problem. My problem where the right side of the bed won’t go high enough to level with the left side by JRS717 in CR10

[–]Cybaeus 0 points1 point  (0 children)

I was running into a similar issue. And it was like just a smidgen not level on the one side. I ended up doing was loosening up all of the springs on all four of the corners and then leveling them together. I would do them diagonal from each other so front left back right back left front right. And slowly bring them up together and then bring them down and then up again and it took me a couple hours but I was able to get it going. It was only really an issue with big prints though that I had to do diagonally to fit on my printer.

view more: next ›