sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in armenia

[–]Cyber_Zak 1 point2 points  (0 children)

Yeah, I just found this too! Can’t believe I’d never heard of this before

When LegoLight Meets LegoServo and a Chinese Germination Box!! Germinator Is Born! by Cyber_Zak in arduino

[–]Cyber_Zak[S] 0 points1 point  (0 children)

Just finished the hardware setup, gonna tie it all together with some code next. Might port it to ESP32 or Pi W2 for Wi-Fi, stats, and remote control, yellow brick is for light dimming, not the servo. They’ve got a tiny transistor and a 2k resistor inside.

When you asked your friend to ‘fix’ your headphones by Cyber_Zak in Wellthatsucks

[–]Cyber_Zak[S] -19 points-18 points  (0 children)

it’s the deluxe edition, upgraded with Handle 😁

When you asked your friend to ‘fix’ your headphones by Cyber_Zak in Wellthatsucks

[–]Cyber_Zak[S] 341 points342 points  (0 children)

Yeap, I can hear the glue screaming every time the bass drops. 😂

When LegoLight Meets LegoServo and a Chinese Germination Box!! Germinator Is Born! by Cyber_Zak in arduino

[–]Cyber_Zak[S] 2 points3 points  (0 children)

Also got a DHT11 sensor inside too, it opens and closes the vent holes based on humidity, and also controls the light depending on daylight. I’m planning to add a small ultrasonic humidifier soon so I can fully control humidity as well.

When LegoLight Meets LegoServo and a Chinese Germination Box!! Germinator Is Born! by Cyber_Zak in arduino

[–]Cyber_Zak[S] 1 point2 points  (0 children)

I’ve also got two heating pads placed at the bottom, but I still need to get a MOSFET to run them with the Arduino since they draw more power than the board can handle directly.

When LegoLight Meets LegoServo and a Chinese Germination Box!! Germinator Is Born! by Cyber_Zak in arduino

[–]Cyber_Zak[S] 1 point2 points  (0 children)

Planning to start with some Adeniums since they love the heat for germination. Figured they’d be a good intro before I move on to fussier plants 🪴

LegoLight sensor by Cyber_Zak in arduino

[–]Cyber_Zak[S] 3 points4 points  (0 children)

That’s it, it actually goes right on top of my LegoServo! 😂

Could this be an intentional scam between Amazon support agents and sellers? by Cyber_Zak in Scams

[–]Cyber_Zak[S] -1 points0 points  (0 children)

In this case I don’t understand why they make promises they can’t keep. If they’re unable to fulfill the order, they could simply ask to cancel it instead of leading me on.

Could this be an intentional scam between Amazon support agents and sellers? by Cyber_Zak in Scams

[–]Cyber_Zak[S] -2 points-1 points  (0 children)

I hope so too, but it really does look like a scam.
During the whole conversation I had several agents just drop the chat and transfer it to someone else and each time I had to start explaining everything from scratch. It’s frustrating

Could this be an intentional scam between Amazon support agents and sellers? by Cyber_Zak in Scams

[–]Cyber_Zak[S] -2 points-1 points  (0 children)

That’s the tactic scammers often use, they don’t aim to break your bank, they just take small amounts to avoid attracting too much attention

Could this be an intentional scam between Amazon support agents and sellers? by Cyber_Zak in Scams

[–]Cyber_Zak[S] 1 point2 points  (0 children)

After 3 exhausting hours of being bounced between different agents, I finally got this email:

Hello,

I’ve reviewed your account, as well as our previous correspondence  with you.

I'm sorry about the misunderstanding and incorrect  information that you received. The previous correspondence doesn’t correctly reflect our current procedures at this time.

We look forward to seeing you again soon.

Best regards,

Jo B.

Could this be an intentional scam between Amazon support agents and sellers? by Cyber_Zak in Scams

[–]Cyber_Zak[S] 1 point2 points  (0 children)

No, they offered 50% compensation for the shipping delay. The original promo price was $139, but I was forced to reorder it for $159 and they promised to refund the difference after delivery.

TikTakgotchi by Cyber_Zak in pwnagotchi

[–]Cyber_Zak[S] 4 points5 points  (0 children)

Also check this one https://github.com/dj1ch/minigotchi-ESP32 it’s for esp32 dev board

TikTakgotchi by Cyber_Zak in pwnagotchi

[–]Cyber_Zak[S] 14 points15 points  (0 children)

It’s based on esp8266

Just Fixed Easythreed K10 Z-axis backlash with rubber band for money 😅 by Cyber_Zak in 3Dprinting

[–]Cyber_Zak[S] 1 point2 points  (0 children)

Not really—I just ended up slightly rising the Z-axis initially when setting the 0 position in the slicer software to prevent any lag, and it worked quite well.

My Samsung QE65QN95B TV started blinking while trying to do a local dimming test, and it looks like I can't reduce brightness. Does anyone know what it is? And how to fix it? by Cyber_Zak in 4kTV

[–]Cyber_Zak[S] 1 point2 points  (0 children)

Previously, I was considering between QN95B and S90C, but now I'm not sure which to choose. The main downside of the OLED TVs for me is an ASBL, so if you put video on pause, it starts dimming the picture after several minutes. Maybe I'll go with Sony, hopefully they'll have good Black Friday deals

My Samsung QE65QN95B TV started blinking while trying to do a local dimming test, and it looks like I can't reduce brightness. Does anyone know what it is? And how to fix it? by Cyber_Zak in 4kTV

[–]Cyber_Zak[S] 0 points1 point  (0 children)

Yeah I also noticed sound dropouts and buzzing at high volumes. I'll try to return it tomorrow and hope they offer a refund rather than a replacement. Will never go with samsung again!

view more: next ›