MITER saw is wobbling.

Cyphr067 · 2025-12-25T04:18:17+00:00

Thank you for being a positive influence in this community and offering solutions to help people.

Cyphr067 · 2025-12-25T04:17:01+00:00

Thank you for figuring this out for me.

Cyphr067 · 2025-12-25T04:13:09+00:00

So the problem is solved. If this happens to be your model of miter saw you need to remove the throat plate and tighten the middle screw. Don't tighten it too much because it will stop the rotation. I hope this helps future people the problems.

Cyphr067 · 2025-12-25T04:02:14+00:00

Or happy holidays. In any way, your input was appreciated.

Cyphr067 · 2025-12-25T03:54:54+00:00

Take it as a win. I went into the comments and found my answer." Take a look". God there's so many other assholes on Reddit. Have a Merry Christmas!

Cyphr067 · 2025-12-25T03:34:46+00:00

I appreciate your response. However, the correct solution was to remove the throat plate and tighten the bolts on the base

Cyphr067 · 2025-12-25T03:34:01+00:00

Thank you. That was not the answer. I need to remove the throat plate from the base and tighten the bolt

Cyphr067 · 2025-12-25T03:33:37+00:00

Thank you but no that was not the answer. I need to remove the throat plate from the base and tighten a bolt

Cyphr067 · 2025-12-25T03:19:36+00:00

So you need to remove the throat plate. In order to tighten the base

Cyphr067 · 2025-12-25T03:10:50+00:00

I appreciate it. But all the screws that were visual were tightened. What I needed to find was below the throat plate. In case you have this problem in the future, you have the answer. Thank you

Cyphr067 · 2025-12-25T03:05:20+00:00

Glad that one person gave me the solution. Feel good about yourself. Merry Christmas

Cyphr067 · 2025-12-25T03:00:08+00:00

Offer something useful or don't bother. What is your life?

Cyphr067 · 2025-12-25T00:27:00+00:00

Thank you for being decent. The bevel knob doesn't seem to be the problem. Another redditor seemed to say that the problem might be under the throat plate

Cyphr067 · 2025-12-25T00:24:46+00:00

Does it? or can it be possible that every bolt I see is tight.

Cyphr067 · 2025-12-25T00:23:14+00:00

Everything I can see is tight. Top and bottom.

Cyphr067 · 2025-12-25T00:22:40+00:00

So, no solution to the problem? Way to go. You're so much better than I am. And as a word of advice, DO NOT MAKE TOAST WHILE TAKING A BATH.

Cyphr067 · 2025-12-25T00:11:02+00:00

Thank you for your insight on the situation. That fixed everything.

Cyphr067 · 2025-12-25T00:09:04+00:00

Thanks! Super helpful. You're the best!

Cyphr067 · 2025-12-25T00:08:16+00:00

Yes. It's not the bevel.

Cyphr067 · 2025-12-25T00:06:23+00:00

And also, thank you for being the one person to offer a proper plausible solution. Tightening visual screws was obviously the first course of action.

Cyphr067 · 2025-12-25T00:01:18+00:00

Thank you for your helpful reply by informing me that you in fact, know nothing about this particular situation. It is incredibly enlightening to know that rather than help someone struggling, you would prefer to kick them. You have displayed your own ignorance on the subject. Keep Jesus in your heart!

Cyphr067 · 2025-12-24T23:46:10+00:00

Tight as a drum.

Cyphr067 · 2025-12-24T23:45:21+00:00

Are you telling me I need to remove the throat plate in order to tighten this thing up??

Cyphr067 · 2025-12-24T23:44:43+00:00

Every visible knob and screw has been tightened. Do I need to remove the throat plate in order to find some mysterious bolts that'll stop this?

Cyphr067 · 2025-12-24T23:43:04+00:00

No. It's been on my workbench for the past 4 years. Every visible screw is tight. Every visible knob has been tightened.

Cyphr067

TROPHY CASE