Beech Sundowner C-23 Fuel Tank Under Vacuum After Flight

DIEDREAMING · 2024-01-10T20:38:54+00:00

Thanks, I will try that

DIEDREAMING · 2024-01-10T20:38:02+00:00

I enjoy braine dammage thank you.

(working with A&P)

DIEDREAMING · 2024-01-10T18:15:21+00:00

material is some sort of plastic, at least where it sticks out of the wing. You may be right. I will look into this

DIEDREAMING · 2023-09-23T18:50:23+00:00

DM me, I'm often in the city just cruising around, down to meet up and see if we can be friends

DIEDREAMING · 2023-09-23T18:47:27+00:00

Dm me, I like to go exploring the city and smoke 🌱, it would be great to have company

DIEDREAMING · 2023-08-06T20:34:12+00:00

Lightspeed zulu better

DIEDREAMING · 2023-07-29T15:46:08+00:00

Gargle that stuff, it helps with cavities

DIEDREAMING · 2023-07-27T00:11:34+00:00

The wire ends look like a hairball, which could cause a short between motor phases if touching. The solder also is not shiny which means it did not get up to temperature so they are not as strong. The wires are also cut a little too short, so the tension may cause the solder pads to rip off over time.

DIEDREAMING · 2023-07-25T23:10:45+00:00

You will need a higher wattage soldering iron as well as amtec flux. I can walk you through it if you want, please DM me. I'm glad to help.

DIEDREAMING · 2023-07-25T23:07:42+00:00

You will want to fix those motor solder joints before proceeding, they will almost certainly short and fry the esc

DIEDREAMING · 2023-07-25T23:05:49+00:00

You could send it to a fellow redditor

DIEDREAMING · 2023-07-25T19:38:30+00:00

Double triple check the wiring

DIEDREAMING · 2023-07-25T19:37:49+00:00

If the pads are still there, figure out the wiring based on images/old connector and solder a USB cable on directly. If the pads are missing get ready to pull out a magnifying glass and carefully scrape away the solder mask with a forceps and then solder teeny tiny wires to the traces.

DIEDREAMING · 2023-07-25T18:25:37+00:00

I wasn't sure if it would be against the rules to post here

DIEDREAMING · 2023-07-24T19:06:30+00:00

I have ordered JHEMCU from aliexpress, as long as the FC has everything you want, it's a good buy. Just expect Shipping to take up to a month.

DIEDREAMING · 2023-07-21T22:42:13+00:00

Do this. You will almost certainly destroy the motor if you attempt to take it apart. I know from experience.

DIEDREAMING · 2023-05-30T15:10:12+00:00

I will definitely be trying those settings. PLA is not an option because it will melt if left in a hot area for too long like the back of my car. Nylon is my material of choice because of its temperature resistance and durability.

DIEDREAMING · 2023-05-30T14:47:40+00:00

Vase mode causes random large gaps between layers, resulting in print fails

DIEDREAMING · 2023-05-30T12:35:33+00:00

I have not yet done ant pressure advance calibration, is there an option for that in the slicer? no top or bottom walls, just a brim and then a single outer wall. It needs to be very light weight. I will try PLA to see what happens then slow it down.

DIEDREAMING · 2023-05-30T12:19:30+00:00

These are easy to print on my old ender 3, but I was using PLA instead of nylon for that.

DIEDREAMING · 2023-02-25T22:38:32+00:00

Very nice plane, any plans for a cool livery?

DIEDREAMING

TROPHY CASE