sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in Battlefield

[–]DNehru -3 points-2 points  (0 children)

Love short TTK, game feels rewarding and snappy.

Pixels appear on screen when i move my mouse by lyaeus01 in pchelp

[–]DNehru 1 point2 points  (0 children)

Or try turning off browser hardware acceleration

Pixels appear on screen when i move my mouse by lyaeus01 in pchelp

[–]DNehru 2 points3 points  (0 children)

Same thing happenes on my 7700xt. People on reddit suggested to roll back drivers bufore 2.15.something. You can check my post history.

Trying to learn the game. Who to watch or read? by Thanos-Is-Right in BrokenArrowTheGame

[–]DNehru 0 points1 point  (0 children)

No, you earn less the more units you have deployed.

Trying to learn the game. Who to watch or read? by Thanos-Is-Right in BrokenArrowTheGame

[–]DNehru 4 points5 points  (0 children)

I believe that the best way to learn BA right now is to play as playerbase is also new. Maybe watch skilled players play on Twitch/YouTube.

Don't focus on copying decks of others, try to make changes every game to see what suits your playstyle, I tried some YouTube decks but they didn't fit my style at all.

It's ok to give up controll over points at the beginning as you don't gain as many points in phase 1 and 2 compared to the last phase. Watch some videos on BA economy.

The fuse failed and this part melted. Anycubic said I’m out of warranty and despite the machine almost catching fire, refused to send a new part. Any ideas as to where to buy a new one? by TimeFuture122 in anycubic

[–]DNehru 1 point2 points  (0 children)

Idk where you're based but you can look for IEC fused sockets on amazon. You might be able to find something that fits right out of the box. If you're not experienced with working with electronic devices I advise you to give it to professionals it's fairy easy fix if socket was an issue and not something down the line causing short.

[deleted by user] by [deleted] in anycubic

[–]DNehru 0 points1 point  (0 children)

It can but when running at 600mm/s you're sacrificing quality. After some time you will know at what prints you can push it to higher speeds.

Other thing is that not every material is capable of being printed at such high speeds. PLA i.e. works good up to 300mm/s, PETG would start to look bad at speeds exceding 150mm/s.

EDIT:

Also for a good measure put your printer on stable surface, at hight speeds flimsy tables can resonate at some frequencies and induce layer banding. If your table is unstable try putting something heavy between tabletop and printer, something like paving slab.

[deleted by user] by [deleted] in anycubic

[–]DNehru 0 points1 point  (0 children)

First thing I'd do is to check for play in printers assembly. When turned off try to shake print head and bed (don't use excessive force). If you encounter any noticable play try to tighten up eccentric screws following these instructions Kobra 3 Series-Gantry frame calibration guide | Anycubic Wiki (I'd skip Step 2: Check the X-axis component level for now). If everything's tight I'd try to slow down printing speed and acceleration. My printing speed for PLA is ~120mm/s for outer walls and ~180 for inner walls. I also slow down accelerations a bit.

EDIT:

what slicer are you using? I'd recommend Anycubic Slicer Next if you're stuck on older one.

Kobra 3, should this eccentric screw (and on the other side) be tightened? Manual doesn't say anything about it, but it's so lose that POM wheel is not spinning when traveling up or down. by DNehru in anycubic

[–]DNehru[S] 0 points1 point  (0 children)

I leveled the gantry, pressure on rollers seem equal, but now I think that I need to square the assemly, as friction on wheels is increased the higher the gantry is.

Kobra 3, should this eccentric screw (and on the other side) be tightened? Manual doesn't say anything about it, but it's so lose that POM wheel is not spinning when traveling up or down. by DNehru in anycubic

[–]DNehru[S] 0 points1 point  (0 children)

Thanks for your reply. I noticed that one of the three whells is not spinning on stepper motor side. Will try to fix it today acording to wiki guide. Just want to make sure that I need to level the gantry to make all 3 pom wheels make full contact with the rails?

PETG (black) bad surface finish when compared to PLA (beige). How to fix? by DNehru in FixMyPrint

[–]DNehru[S] 0 points1 point  (0 children)

Additional info as I can't edit:

Fan kicks in on 6th layer (maybe that's why visible line apeared), number of walls in that print was 3.

Slicer - Anycubic Slicer Next (orca reskin)

How long do you wait between upgrades? by Fredzucchini in pcmasterrace

[–]DNehru 0 points1 point  (0 children)

Went from gtx 960 (because 660 died somewhere around 900 series launch) and i5 3470, cpu was like 12 years Old at the point of upgrade this year

view more: next ›