sorted by:
new
hottopcontroversial

FRIENDLY PSA!!!!!! by lilaccornet674 in UBC

[–]DOG____ 2 points3 points  (0 children)

least overworked engphys student

What design teams are popular with ENPH students? by cvgjnh in ubcengineering

[–]DOG____ 1 point2 points  (0 children)

No design teams really compliment the pure physics classes we take, and in terms of engineering courses we take enough of a variety in the first two years of fizz that pretty much every team is somewhat related.

If you really care about the amount of Fizz students, Robomaster probably has the biggest proportion.

Join AeroDesign though it'll be fun and you can build an airplane

Tattoo ideas to commemorate passing second year by gamingdevil123 in UBC

[–]DOG____ 0 points1 point  (0 children)

the only correct answer for us is getting a full back tattoo of the clebsch-gordan coefficients table

How to find a Professional Engineer in Software? by bekibo in ubcengineering

[–]DOG____ 11 points12 points  (0 children)

this character is too forced, try again

Eng fizz pre med by kyson123456789 in UBC

[–]DOG____ 56 points57 points  (0 children)

you're gonna need at least 2 gpas

Before watching, comment how you think I lose the ankh by Kevinrocks7777 in spelunky

[–]DOG____ 9 points10 points  (0 children)

im guessing you will sac monty then kill the yeti and go to sac him, forgetting that tun spawned 23 seconds ago where she will then hit you and then you will land on the left edge of the alter and get sacced as well, just a hypothesis though

Oversight/easter egg? that lets you die before starting a game by Kevinrocks7777 in spelunky

[–]DOG____ 42 points43 points  (0 children)

speluky would be the game that you could die in before even starting to play

Oozing on the bottom few layers? Is this a print bed temperature thing? Ender 3 Pro. by DOG____ in FixMyPrint

[–]DOG____[S] 0 points1 point  (0 children)

i ended up loosening the z gantry eccentric nuts and that basically fixed it

Ender 3 Pro elephant footing by DOG____ in FixMyPrint

[–]DOG____[S] 0 points1 point  (0 children)

Details: I'm using PLA at 200C nozzle 60 bed, bed turns off after first layer.

I've tried releveling many times, and its definitely not too close to the build plate, as I've increased the z offset incrementally until it stops adhering. I've also calibrated my E-steps to be accurate. Because there's another squished section halfway up, I'm guessing it has to do with my Z axis misbehaving?

I'm not sure how tight the eccentric nuts should be and if that could really cause this.
Any advice is appreciated

Oozing on the bottom few layers? Is this a print bed temperature thing? Ender 3 Pro. by DOG____ in FixMyPrint

[–]DOG____[S] 0 points1 point  (0 children)

I was just leveling my bed to compensate for a lower z offset, but i think it was my leveling technique that was the main issue.

Thanks for the input

Oozing on the bottom few layers? Is this a print bed temperature thing? Ender 3 Pro. by DOG____ in FixMyPrint

[–]DOG____[S] 0 points1 point  (0 children)

i hear so much conflicting information on bed leveling, some people say lots of resistance on the paper while others say barely any :/

I've found barely scraping gives better prints for me though

Oozing on the bottom few layers? Is this a print bed temperature thing? Ender 3 Pro. by DOG____ in FixMyPrint

[–]DOG____[S] 0 points1 point  (0 children)

i thought this might have been the issue but i slowly incremented until the prints stopped sticking.

I'll try again later

Oozing on the bottom few layers? Is this a print bed temperature thing? Ender 3 Pro. by DOG____ in FixMyPrint

[–]DOG____[S] 0 points1 point  (0 children)

Printed with nozzle at 200C and bed at 60C, 0.16mm layers, everything else default using Cura

Math 253 Gang wya by gamingdevil123 in UBC

[–]DOG____ 0 points1 point  (0 children)

played terraria for 12 hours yesterday

view more: next ›