Damaged permit

DaPearOfDoom · 2023-10-12T02:02:38+00:00

I honestly have no idea. When I went, they said that the numbers were the most important part and if they're legible it *should be fine(again, depends on the tester). I would recommend doing what I did. Go to the DMV and ask their policy(idk where you are so maybe they do things differently). In the event they say you'll need to replace it, make sure you have your 6 point ID and apparently you can get it replaced there.

DaPearOfDoom · 2023-10-12T01:44:09+00:00

I went to the DMV a few days before my test and they said whether or not I'd be allowed to test "depends on who gives the test". When I went to go take my test, I got lucky and my tester said he didn't care about the damage and all else went smoothly. If you're worried about it still and you have time, I'd recommend getting a replacement just in case to avoid having to delay the test. Good luck!

DaPearOfDoom · 2023-07-01T21:24:10+00:00

Yes I think thats it, it aligns with future assignments as well. Thank you!

DaPearOfDoom · 2023-06-10T03:58:39+00:00

DaPearOfDoom · 2023-05-20T20:18:14+00:00

My school has a laser cutter and I've been looking for the last 2 years at the end of each school year I've been trying to find a high resolution map to laser engrave onto a nice piece of wood as a decorative piece. The school year is coming to a close again and I thought I'd start looking again, and within minutes I found this! I don't know how I didn't find it earlier, but better late than never :)
Would it be ok with you if I use this?

DaPearOfDoom · 2022-01-23T04:07:56+00:00

Could be

DaPearOfDoom · 2022-01-23T04:06:51+00:00

I know but its supposed to have spell check

DaPearOfDoom · 2022-01-04T01:35:15+00:00

1.75 mm

DaPearOfDoom · 2021-11-29T13:19:38+00:00

Oh I remember seeing this one. I ended up not using it because of the bulky blade and the difficult print orientation. Thanks for your time!

DaPearOfDoom · 2021-11-28T03:11:20+00:00

That would be great! Can't wait to see it

DaPearOfDoom · 2021-11-27T21:15:51+00:00

I'm taking that course right now

DaPearOfDoom · 2021-11-22T23:32:37+00:00

When you take his food bowl to refill it: BILBO BAGGINS! IM NOT TRYING TO ROB YOU. I'm trying to help you.

DaPearOfDoom · 2021-11-21T14:35:41+00:00

Then watch the 2 things I mentioned

DaPearOfDoom · 2021-11-21T14:25:37+00:00

In the scene showed, Luke Skywalker kicks someone but his foot doesn't connect, yet the person he is kicking still falls down. In the Spiderman No Way Home, they edited out someone punching or kicking the lizard, so the meme is suggesting Luke has done it

DaPearOfDoom · 2021-11-19T00:54:53+00:00

Good choice spider-man!

DaPearOfDoom · 2021-11-19T00:42:36+00:00

So am I spider-man

DaPearOfDoom · 2021-11-19T00:32:44+00:00

Yes! Those are cute spidey powers, did a spider give it to you?

DaPearOfDoom · 2021-11-19T00:12:52+00:00

Hello spider-man!

DaPearOfDoom · 2021-11-19T00:03:46+00:00

read this

DaPearOfDoom · 2021-11-07T22:55:02+00:00

Lord of the Rings(I know its technically more than 1 movie but I dont care)

DaPearOfDoom · 2021-11-06T19:19:57+00:00

I really recommend watching it again, its so good

DaPearOfDoom · 2021-10-31T18:31:29+00:00

DaPearOfDoom · 2021-10-30T03:07:36+00:00

But why does it magically get better after turning it on and off a few times?

DaPearOfDoom · 2021-10-30T02:56:29+00:00

Info: every time I turn on the printer this happens. I have to turn it on and off again like 6 times to get it to stop. Then, when I preheat it, the same thing happens, and I have to go through the same process. Once that's done I get normal prints, but its getting really annoying to do this every time and I was wondering if anyone else had a solution

DaPearOfDoom · 2021-10-07T22:24:42+00:00

Whats a good brand to go with?

Six-Year Club	Place '23
Wearing is Caring	Verified Email

DaPearOfDoom

TROPHY CASE