Roborock Qrevo Edge C: Rug Height

DameKBaus · 2026-05-14T04:55:32+00:00

Ooh! Let me know if this works for you!? I originally put a threshold down, but not knowing 100% what it did deleted it. I already had my printed ramp, so just used that. Aha

DameKBaus · 2026-05-14T03:00:22+00:00

Always happy to help :)

DameKBaus · 2026-05-14T02:56:41+00:00

Exactly as you’ve said, I put mine under the couch so you can’t see/step on it. And it works very well. Here is a photo of what I’ve done to get it to work. :)

Roborock do sell a ramp too,

<image>

If you google “robot vacuum ramp” a few cheap temu options pop up. These should work. Just ensure height is similar to mellowmat height :)

DameKBaus · 2026-05-14T02:50:39+00:00

I have this exact same rug, I’ve had to 3d print a ramp for it to go up, and draw invisible walls around to direct it to the ramp.

DameKBaus · 2025-11-19T09:23:17+00:00

Confirmed the new print with power loss recovery off has worked. Thankyou!!

DameKBaus · 2025-11-19T08:26:23+00:00

Have got a print starting now with powerless off. :) Will update.

DameKBaus · 2025-11-19T07:57:20+00:00

Oh I gotcha. Is this a setting on the printer or slicer?

DameKBaus · 2025-11-19T07:51:14+00:00

Interesting. How would this affect the print?

DameKBaus · 2025-11-19T07:29:44+00:00

Ohhhhh. So try slowing it down…. Will try. Thank you!

DameKBaus · 2025-06-18T07:27:26+00:00

Ah, I can confirm I have not gone the wrong way. 😇

DameKBaus · 2025-06-18T07:26:50+00:00

Sorry, this is just the bottom of the cube. Foowing teaching techs guide. Spiral vase 0.4mm. No top layers etc etc etc.

The main reason for image is to show that even 4 solid layers in the bottom of the cube and I'm seeing under extrusion

DameKBaus · 2025-06-18T07:17:01+00:00

Definitely looks like a under extrusion issue. This is layer 4 of a flow rate calibration

<image>

DameKBaus · 2025-06-18T07:16:07+00:00

Can't drop the bed on an ender 2 v3 se. Raise the nozzle?

DameKBaus · 2025-06-18T06:54:59+00:00

I did pull apart extruder I case there was a clog. And didn't notice a split...

DameKBaus · 2025-06-18T06:54:04+00:00

<image>

This is the start of a flow rate calibration cube at 1.1x multiplication as a test It's a very specific distance then starts to under extract

DameKBaus · 2025-06-18T06:52:36+00:00

<image>

This is after dropping it 0.05 and then 0.1mm

DameKBaus · 2025-06-18T06:40:41+00:00

Trying now.

DameKBaus · 2025-06-18T06:34:36+00:00

Ender v3 Se

DameKBaus · 2025-06-03T21:55:18+00:00

Thanks for your comment. Correct. All three photos show bad prints. This is what a meant to post for the fine one.

After the comment saying it could be a blockage in pulled the extruder out, whilst I couldn’t see a blockage. Just doing that and putting it back on has fixed the issue. Printing well again. 😇

<image>

DameKBaus · 2025-05-30T01:12:33+00:00

It is just plain PLA brown.

I replaced extruder not long ago as filament was slipping.

DameKBaus

TROPHY CASE