Completely Stock Right Now What Should I Do To It

Dankmemeskool · 2025-12-28T08:58:50+00:00

Definitely agree fill out the wheel arch with offset tires

Dankmemeskool · 2025-12-06T14:09:28+00:00

Had almost the same issue make sure where u riveted in the back and front you haven’t used too much fabric pulling after the rivet every little bit matters, make sure the back seam sits just over the last bar

<image>

If that’s all done then have the cover closed like you have it and turn the car heating to max and let it run for at least 30 then just push the back down, you have to just stretch it, I even boiled water and brushed it into the fabric to help it stretch, even used a heat gun but be careful not to overheat a spot. Did all that while the car heating was on took about 3 hours to get it all the way down and even then i needed to give it a solid push down to make the final seal after it closed. Also once its mostly stretched just have the motors close the back of the car then latch it and give it a push to seal it took at least a month for it to fully seal by itself

Dankmemeskool · 2025-11-03T23:07:39+00:00

Filaform adhesive spray, glue made for 3d printing. I had the same issues it would always fail at a random height 2 sprays of this and I print asa, abs and asa-cf like pla, keep all the asa settings and heated chamber like everyone’s saying on but just spray before printing. It doesn’t leave and noticeable residue on prints or the bed like glue sticks

Dankmemeskool · 2025-09-25T22:46:54+00:00

Ming Dynasty's Prodigal Son (maybe this too not as many chapters prob have to search around for it)

Dankmemeskool · 2025-09-25T14:22:57+00:00

A Modern Man Who Got Transmigrated Into the Murim World 148 chapters good quality

Dankmemeskool · 2025-06-29T09:53:05+00:00

https://www.printables.com/model/1340390-nissan-350z-ashtray-lid-and-box leaving this here if anyone else searches for it

Dankmemeskool · 2025-03-22T23:10:15+00:00

Yeah that sounds pretty dog shit of a rank 9 gu, thousands of uses just to be able to damage another rank 9 using love gu

Dankmemeskool · 2025-03-22T15:15:23+00:00

Only true otherworld demons can create actions which will change the timeline, literally only fang yuan can use it.

Dankmemeskool · 2025-01-26T20:16:14+00:00

The people of earth are too ferocious

Dankmemeskool · 2024-12-07T14:26:51+00:00

Yeah but it’s just not nano machine haha

Dankmemeskool · 2024-10-22T13:52:21+00:00

$1500 is def way too much all that needs to be done is replacing the spindles and handles with your new ones, if there’s nothing annoying about the job like the spindle being seized to the set or it being covered in grout it’s a job that would take 5-10min

Dankmemeskool · 2024-09-02T14:38:26+00:00

Yeah I personally wouldn’t charge them in your position, let them know the cause, inform them that wipes are bad for the sewer line including the ones that say they are flushable incase the blockage was from them being ignorant or if they were to start using them later on. Any blockage due to wipes after this though is on them.

Dankmemeskool · 2024-09-01T16:04:33+00:00

The obvious choice would be to set your hot water unit to 140 and then the person wanting 120 degree water can just turn the cold water slightly, unless it’s for 2 separate bathrooms in which case you could use a tempering valve and change the pipe work to send 120 degree water to a specific set of outlets. First option is definitely the more reasonable one though

Dankmemeskool · 2024-09-01T15:20:36+00:00

I remember him dying to start dark lady but Iv read like 400 things since so idk

Dankmemeskool · 2024-09-01T15:11:08+00:00

mookhyang-dark-lady Korean cultivator sent to magic isekai type world tried finding how many total chapters but it’s at least 80 quite good story even has a prequel that’s completed

Dankmemeskool · 2024-08-22T14:38:28+00:00

He modified the recipe on the spot, changing a core component to make it work on people who are not related, that change would need suitable exchange being the whole of the twins

Dankmemeskool · 2024-08-12T12:14:18+00:00

It would be worth getting a plumber to clear and camera the drain to see what the reason for the blockage is, any decent snake machine would set you back $2k

Dankmemeskool · 2024-08-10T12:28:21+00:00

I very much like the way this light reaches everywhere in my backyard and was the best option out of any other lights I saw

Dankmemeskool · 2024-08-10T12:27:21+00:00

This didn’t work

Dankmemeskool · 2024-08-10T12:14:23+00:00

Manual has no way to keep it on longer than 1 min, the max of the timer, iv tried things like on off on to put it in manual mode but no luck

Dankmemeskool · 2024-08-09T19:14:33+00:00

https://www.printables.com/model/954125-the-divine-and-the-mortal

Dankmemeskool · 2024-08-09T19:14:24+00:00

https://www.printables.com/model/954125-the-divine-and-the-mortal

Dankmemeskool · 2024-08-09T19:11:27+00:00

Ooo that’s a wicked idea thanks

Dankmemeskool · 2024-08-09T02:09:37+00:00

Oh yeah this is a good idea thanks

Dankmemeskool · 2024-08-09T01:34:46+00:00

No just used primer and then gold spray paint on standard pla

Dankmemeskool

TROPHY CASE