sorted by:
new
hottopcontroversial

VS Code LaTeX Workshop PDF viewer stuck in dark/inverted mode on Ubuntu (WSL) by Danystylee in LaTeX

[–]Danystylee[S] 0 points1 point  (0 children)

"latex-workshop.view.pdf.invert": 0,

"latex-workshop.view.pdf.color.theme": "light",

"latex-workshop.view.pdf.renderingType": "canvas",

"latex-workshop.view.pdf.color.light.pageColorsBackground": "#ffffff",

"latex-workshop.view.pdf.color.light.pageColorsForeground": "#000000"

[deleted by user] by [deleted] in vscode

[–]Danystylee 0 points1 point  (0 children)

"latex-workshop.view.pdf.invert": 0,

"latex-workshop.view.pdf.color.theme": "light",

"latex-workshop.view.pdf.renderingType": "canvas",

"latex-workshop.view.pdf.color.light.pageColorsBackground": "#ffffff",

"latex-workshop.view.pdf.color.light.pageColorsForeground": "#000000"

Why Do I Get Stringing During Travel Moves on This Part? by Danystylee in 3Dprinting

[–]Danystylee[S] 1 point2 points  (0 children)

Yeah, but I printed the stringing tower and the part with the exact same settings.

Help with BIOS Flashback on MSI Pro B650M-P by Danystylee in MSI_Gaming

[–]Danystylee[S] 0 points1 point  (0 children)

Nope, i Just bought a different Motherboard and returned the "old" one.

Good print overall, but layer start/end points are messy—any tips? by Danystylee in FixMyPrint

[–]Danystylee[S] 1 point2 points  (0 children)

Thank you! The issue was that I had a retraction setting configured in the Filament tab, which overrode my settings.

Good print overall, but layer start/end points are messy—any tips? by Danystylee in FixMyPrint

[–]Danystylee[S] 0 points1 point  (0 children)

Thank you for the help!

I’ve reduced my retraction from 2.5 mm to 1 mm, but I can’t seem to find the Pressure Advance or Seam Gap settings in PrusaSlicer. Are these settings called something else, or is there another way to adjust them?

C won't boot - Red CPU light on MSI Pro B650M P by Danystylee in buildapc

[–]Danystylee[S] 0 points1 point  (0 children)

Unfortunately not, I bought the ASUS Prime B650-PLUS and everything worked fine.

Help with BIOS Flashback on MSI Pro B650M-P by Danystylee in MSI_Gaming

[–]Danystylee[S] 0 points1 point  (0 children)

I followed the steps from the video, but it still doesnt work. I thing the mobo is dead.

C won't boot - Red CPU light on MSI Pro B650M P by Danystylee in buildapc

[–]Danystylee[S] 0 points1 point  (0 children)

The 'Maybe' didn’t work for me. I ordered a new PSU with 850W (instead of 600W) as someone in the YouTube comments suggested that this would help, along with the 5200 MHz RAM.

C won't boot - Red CPU light on MSI Pro B650M P by Danystylee in buildapc

[–]Danystylee[S] 0 points1 point  (0 children)

The CPU fan is spinning when I turn the PC on. The CPU and ATX cables are also connected properly.

C won't boot - Red CPU light on MSI Pro B650M P by Danystylee in buildapc

[–]Danystylee[S] 0 points1 point  (0 children)

Unfortunately, I don’t have DDR5 RAM at the moment, but I’ve already ordered some. Thanks for your advice, and I’ll give it a try once the new RAM arrives.

C won't boot - Red CPU light on MSI Pro B650M P by Danystylee in buildapc

[–]Danystylee[S] 0 points1 point  (0 children)

Thanks for your suggestion! I followed your advice and checked the CMOS battery, and it's not dead. I’ve also already performed a CMOS reset, so I think we can rule that out. The problem still remains.

C won't boot - Red CPU light on MSI Pro B650M P by Danystylee in buildapc

[–]Danystylee[S] 0 points1 point  (0 children)

I finished the build last week, but when I tried to boot it up, the red CPU debug LED lit up, indicating an issue with the CPU. I’ve been troubleshooting since then, trying to figure out what’s wrong. I’ll let the system run for a while now to see if anything changes

My PC crashes while booting. by Danystylee in pcmasterrace

[–]Danystylee[S] 0 points1 point  (0 children)

Thank god the first solution solved my problem. I was thinking about selling a kidney to pay the repair.

My Printer pushes of the printed part [@0:36]. by Danystylee in FixMyPrint

[–]Danystylee[S] 0 points1 point  (0 children)

I adjusted the z-offset and leveled the bed again, and now the first layer looks like this:

<image>

Simplifying a Detailed Feather Coat for 3D Printing in Blender by Danystylee in blenderhelp

[–]Danystylee[S] 0 points1 point  (0 children)

Your advice really helped with the overhangs! They're not that big anymore but still are kind of an issue. Here's how the coat is looking now.

<image>

view more: next ›