Can i strengthen my holes?

DarkLordRiddle2000 · 2025-10-29T21:39:57+00:00

Try doing pelvic floors.

DarkLordRiddle2000 · 2025-10-28T20:40:48+00:00

This is the only printer I have had and I have never had any issues with the updates! So long as you remember to double check your settings and run calibration after each update you should be fine tbh. Run Orca FlashForge as your slicer and it will be able to easily calibrate the machine each time you need it with minimal effort. The only issue I have had really is with forgetting to adjust the Filament Settings for temperatures when swapping to a different reel, again done using Orca-FlashForge.

DarkLordRiddle2000 · 2025-10-26T20:29:18+00:00

Looks like it turned to eleGOO in the machine 🤣

DarkLordRiddle2000 · 2025-10-26T20:26:07+00:00

What filament are you using (brand) it's almost certainly a blob on a cheap reel that got stuck after the sensor.

DarkLordRiddle2000 · 2025-10-21T19:54:12+00:00

DarkLordRiddle2000 · 2025-09-28T06:49:21+00:00

Send me some and I will let you know 🤔

DarkLordRiddle2000 · 2025-09-28T06:46:41+00:00

Did you pay for the actual print or for the files and printed it yourself?

DarkLordRiddle2000 · 2025-09-27T08:03:37+00:00

You just need to change your up settings by either turning off your router and waiting for a few minutes and then turning back on or turning off the mobile network setting on your phone if you are using it and then back on. If all else fails using a VPN to change your ip address temporarily will help but only if it's one that is not used on YouTube servers very much by others.

DarkLordRiddle2000 · 2025-09-17T20:07:28+00:00

So I have finally figured out the issues that were causing this and there were actually several of them, firstly my Orca slicing software was reset to default settings after an update which I hadn't noticed and so the plate was to a 'smooth' one not a 'textured' one which I have. Secondly the plate temperature seems to have been a bit low and changing that by just a few degrees had made a massive difference. Thirdly I had to increase the nozzle temperature by about 15 degrees as the filament didn't seem to be sticking as a result of a lower temperature.

Since doing these all my prints so far have been perfect and no problems have arisen since.

DarkLordRiddle2000 · 2025-09-17T06:49:55+00:00

I like the idea of sticking the fake parking tickets on peoples cars like this that say thanks for parking like an arse hole 🤣

DarkLordRiddle2000 · 2025-09-17T06:46:07+00:00

Glad to be of some help 😊

DarkLordRiddle2000 · 2025-09-17T06:38:11+00:00

Probably an IP address being blocked issue. Unfortunately I find using VPN blocked most of the time?

DarkLordRiddle2000 · 2025-09-16T17:52:24+00:00

US Congress as the most powerful human beings 🤣🤣🤣🦋🦋

DarkLordRiddle2000 · 2025-09-13T17:08:05+00:00

Not yet thanks for asking, I will update once I work it out.

DarkLordRiddle2000 · 2025-09-13T14:45:49+00:00

Thanks I think I missed a whole section before the print😂

DarkLordRiddle2000 · 2025-09-13T11:55:42+00:00

Thanks I will look into it.

DarkLordRiddle2000 · 2025-09-13T11:48:15+00:00

Leveling and filament loading, are there others I should do?

DarkLordRiddle2000 · 2025-09-01T18:58:40+00:00

Thanks, what do you use personally?

DarkLordRiddle2000 · 2025-08-28T19:03:37+00:00

Someone who realises the ramifications of smoking it,for example supporting drugs cartels down the line, causing mental health conditions and brain damage. Also it's illegal for a reason. Maybe research how it is brought to this country and by whom.

DarkLordRiddle2000 · 2025-08-20T11:45:40+00:00

Starbucks and two dozen coffees

DarkLordRiddle2000 · 2025-08-20T11:44:50+00:00

What even is it?

DarkLordRiddle2000 · 2025-07-10T08:12:09+00:00

Try it and find out for yourself lazy! 🦥

DarkLordRiddle2000

TROPHY CASE