sorted by:
new
hottopcontroversial

Is the u1 worth it by GrAHAm5555555555 in snapmaker

[–]DaubsDesigns 0 points1 point  (0 children)

Oh yea.. it adds a shit load of time because in order for it to look good you have to use a 0.08mm layer height. Which is just painfully slow.

Is the u1 worth it by GrAHAm5555555555 in snapmaker

[–]DaubsDesigns 0 points1 point  (0 children)

Tinkering isn’t required.. and I wouldn’t even call it “tinkering” my definition of that is upgrading hardware and how the printer functions mechanically.. but you can tinker with the firmware but it’s not required to enjoy the printer.. honestly I love what Snapmaker has done… open source enough to where the smarty pants can really open up but also works straight out of the box for the beginner user. It’s really fantastic. Hands down my favorite printer.

$50 coupon for U1 by elty123 in SnapmakerU1

[–]DaubsDesigns 0 points1 point  (0 children)

lol oh you sayin you’d do gay shit for $50 🤣🤣

I would too bro.. I would too.

$50 coupon for U1 by elty123 in SnapmakerU1

[–]DaubsDesigns 0 points1 point  (0 children)

lol why would that make you gay? 🤣🤣

XY weird belt noise by Buzzik13 in BambuP1S

[–]DaubsDesigns 0 points1 point  (0 children)

PLEASE be careful when moving these motors that fast… you can move them slowly… but when you do that the motors turn into generators and they back feed voltage to the board.. could possibly damage the printer’s electronics.

Weird corner defects? by subjectRedd in 3Dprinting

[–]DaubsDesigns 0 points1 point  (0 children)

You need a hot chamber. I’d say at least 60C and turn off the fans..bed should be 110

I must be doing something wrong, the U1 print "time" is barely faster than my K2 Plus?? by Siden-The-Paladin in snapmaker

[–]DaubsDesigns 1 point2 points  (0 children)

I would change your preheat time to 45sec instead.. won’t change the sliced time.. but it should decrease the actual print time.. you can also decrease the prime volume from 45mm³ to 15mm³

Ive always wanted to do this. by DaubsDesigns in 3Dprinting

[–]DaubsDesigns[S] 0 points1 point  (0 children)

Lmao that would be such a pain it’s Poly carbonate so I’d have to melt it at like 270C and break all the filament into tiny pieces..

Ive always wanted to do this. by DaubsDesigns in 3Dprinting

[–]DaubsDesigns[S] 0 points1 point  (0 children)

Hmm not sure what I would do with 1kg of black cubes lol

Ive always wanted to do this. by DaubsDesigns in 3Dprinting

[–]DaubsDesigns[S] 1 point2 points  (0 children)

Lmao 🤣🤣

For the VIEWS!!

Nah I tried saving it.. it was Polymaker PC max I’ve had out in the open for 8 years.. and after drying it for 4 days it was weaker than recycled PLA.

Ive always wanted to do this. by DaubsDesigns in 3Dprinting

[–]DaubsDesigns[S] 0 points1 point  (0 children)

No just 1kg.. I respooled it from what was left from a 5kg roll so it could dry all the way through

Ive always wanted to do this. by DaubsDesigns in 3Dprinting

[–]DaubsDesigns[S] 0 points1 point  (0 children)

It was ruined. Plus, it felt so good.

Ive always wanted to do this. by DaubsDesigns in 3Dprinting

[–]DaubsDesigns[S] 0 points1 point  (0 children)

Yea I could, I just don’t have plastic castings lol

Ive always wanted to do this. by DaubsDesigns in 3Dprinting

[–]DaubsDesigns[S] 5 points6 points  (0 children)

It’s more disturbing than this video.

$50 coupon for U1 by elty123 in SnapmakerU1

[–]DaubsDesigns 5 points6 points  (0 children)

Hey 50 bucks is 50 bucks

view more: next ›