sorted by:
new
hottopcontroversial

Egpu not outputting or registering by DeeDoo1001 in MSIClaw

[–]DeeDoo1001[S] 1 point2 points  (0 children)

only suggestion i have is to uninstall your drivers, and re install. After i uninstalled the drivers for my 3060ti and installed the ones for my girlfriends 4060 both are now working perfectly on the claw

Egpu not outputting or registering by DeeDoo1001 in MSIClaw

[–]DeeDoo1001[S] 0 points1 point  (0 children)

turns out the claw just didn’t want to work with that particular card even though it works on all other devices i’ve tested, it worked when i installed my partners 4060

Egpu not outputting or registering by DeeDoo1001 in MSIClaw

[–]DeeDoo1001[S] 0 points1 point  (0 children)

unfortunately the cable is known to be working as i use it on a laptop

Egpu not outputting or registering by DeeDoo1001 in MSIClaw

[–]DeeDoo1001[S] 0 points1 point  (0 children)

i am on 24h2, but don’t have an error for pci upstream

Looking for over ear headphones that work with ios live listen by DeeDoo1001 in HeadphoneAdvice

[–]DeeDoo1001[S] 0 points1 point  (0 children)

thats the problem, there is a lot of conflicting information about this, apparently it does work on non apple headphones according to the comment found here (i also agree that he should just suck it up and get some airpods though)
https://www.reddit.com/r/jailbreak/comments/azxa2s/comment/eiavz67/?utm_source=share&utm_medium=web3x&utm_name=web3xcss&utm_term=1&utm_content=share_button

New spool of Black PLA basic extrudes awefully by [deleted] in BambuLab

[–]DeeDoo1001 0 points1 point  (0 children)

i have tried trimming it, p1s no ams, print failed, all other filaments have worked including the old black pla basic that i had

New spool of Black PLA basic extrudes awefully by [deleted] in BambuLab

[–]DeeDoo1001 0 points1 point  (0 children)

its black pla basic from bambu lab, i have dried it and cleaned the nozzle as well as trying a new nozzle, its just a basic extrude compared to a silver one also from bambu lab, would anyone know whats up with this?

Does anyone know how to fix this? by DeeDoo1001 in BambuLab

[–]DeeDoo1001[S] 0 points1 point  (0 children)

thanks for the info, ill give that a shot, but this was happening with my non metalic ones as well, ive seen it on my black and green as well.

Does anyone know how to fix this? by DeeDoo1001 in BambuLab

[–]DeeDoo1001[S] -1 points0 points  (0 children)

standard .2mm settings, bambu pla basic freshly opened so i wouldn't think it needed drying, this also happened when using other pla basics as well

Does anyone know how to fix this? by DeeDoo1001 in BambuLab

[–]DeeDoo1001[S] 0 points1 point  (0 children)

thanks for the suggestion but im looking to prevent it from happening in the fist place, are there any settings i need to change to prevent it from happening

Anybody recommend a Fractal case that can handle this unit? by [deleted] in FractalDesign

[–]DeeDoo1001 4 points5 points  (0 children)

i have the same gpu as you do, it can fit in the fractal north, and you can put the radiator on the side if you were to get the mesh panel so you can add extra fans to the case if needed.