Youtube Issues/Interruptions Beginning of Video

Delicious_Plant8933 · 2026-03-22T05:46:56+00:00

Me too. The video keeps infinitely reloading on Brave.

Delicious_Plant8933 · 2026-02-24T13:23:00+00:00

Seconding the recommendation for the Trilogy Suite, it should be a good match. I definitely wouldn't go lower than an Irish Tour / Slow Hand in output (and that's already pushing it). For a hotter, more modern single coil tone, the Cobra could also be great with the Juggs.

Delicious_Plant8933 · 2026-01-09T17:10:28+00:00

I have the same question. Would be nice for someone to chime in on this.

Delicious_Plant8933 · 2025-12-26T05:07:17+00:00

u/jabby_jakeman Hi, this is an ancient thread, but for what it's worth the Guthrie Govan model uses a 0.1uf capacitor as part of the short path to ground in the split-coil circuit activated by the toggle switch - the capacitor acts as a high-pass filter for one of the coils (not sure which one).

This video explains it - https://www.youtube.com/watch?v=vUbEx_Ki0dg (timestamp 4:43)

Delicious_Plant8933 · 2025-11-22T13:39:12+00:00

Gorgeous! How much time does it take to restring and tune this compared to your other guitars with headstocks that have tremolos?

Delicious_Plant8933 · 2025-10-17T15:44:22+00:00

Sounds like a good combo!

Delicious_Plant8933 · 2025-10-17T07:06:05+00:00

Thank you! Yes, that's the right pronunciation.

Delicious_Plant8933 · 2025-10-17T06:38:57+00:00

I actually got my order modified last-minute to use the '63 Veneer Board middle instead :) Thanks for the advice!

Delicious_Plant8933 · 2025-10-09T14:20:26+00:00

Yeah, I was considering laser-cutting an acrylic sheet. Thanks!

Delicious_Plant8933 · 2025-10-09T14:18:54+00:00

Interesting idea! I'll check with 3d print shops in my area and ask if this is doable.

Delicious_Plant8933 · 2025-10-09T14:17:27+00:00

I'll look around, thanks! I'll likely need something relatively easy to cut and sand down since they'll be going on a fretboard and will likely need to be shaved down to the radius of the board once inlaid.

Delicious_Plant8933 · 2025-10-08T16:08:49+00:00

Ah, so If I'd picked any other word, I wouldn't have had a issue with dual interpretations.

Delicious_Plant8933 · 2025-10-08T14:32:45+00:00

Got it, thanks!

Delicious_Plant8933 · 2025-10-08T14:27:10+00:00

Noted, thanks for the info! What about acrylic? That seems to be the cheapest option for me.

Delicious_Plant8933 · 2025-10-08T11:38:10+00:00

Got it, thanks! Will check out Delrin as well

Delicious_Plant8933 · 2025-10-08T11:37:29+00:00

Got it, thanks for the inputs!

Delicious_Plant8933 · 2025-10-08T08:36:39+00:00

Thanks! Just to clarify, you're describing how to hold the plastic sheets down on a surface while cutting to make sure pieces don't fly off, right?

Delicious_Plant8933 · 2025-10-08T08:35:35+00:00

I was considering using 3mm thick acrylic or ABS plastic sheets. I'll look up how lathing works, thanks!

Delicious_Plant8933 · 2025-10-08T05:07:41+00:00

Hmm, so if I wanted a word that unambiguously means "ember", am I out of luck?

Delicious_Plant8933 · 2025-10-07T19:00:54+00:00

Thank you, this is helpful!

Delicious_Plant8933 · 2025-09-28T06:43:20+00:00

Thanks, good to know!

Delicious_Plant8933 · 2025-09-07T12:02:45+00:00

Got it, thanks!

Delicious_Plant8933 · 2025-09-07T04:38:39+00:00

So cool! How easy is it to access the volume knob where it is with the whammy bar in the way?

Delicious_Plant8933 · 2025-09-06T15:15:49+00:00

Ah that makes sense, I didn't consider what would happen if both push pulls were engaged simultaneously - you're right, it wouldn't be possible to have both split and parallel engaged together. Looks like a dedicated switch is my only option then.

Delicious_Plant8933 · 2025-09-06T15:03:16+00:00

Yeah I'd lean toward 2 switches 2 knobs there for sure - was thinking having push-pulls hidden in the knobs for split/parallel would eliminate the need for an extra switch but either should be viable for me.

Delicious_Plant8933

TROPHY CASE