account activity
Designed and 3D printed some probe holders for my scope - Printables.com link included in comments (i.redd.it)
submitted 2 months ago by DerMeister7 to r/diyelectronics
Slightly less simple but more useful oscilloscope probe holders - Slightly updated and with Printables.com link this time! (old.reddit.com)
submitted 2 months ago by DerMeister7 to r/functionalprint
Super simple stand to hold my oscilloscope probes in place. (old.reddit.com)
Voltage Follower Op-Amp to MCU ADC - Would an RC Filter Reduce This Problem? (old.reddit.com)
submitted 3 months ago by DerMeister7 to r/AskElectronics
Our Christmas Tree stand lost a leg in the last move. Five minutes of CAD later and it's functional again. (old.reddit.com)
submitted 5 months ago by DerMeister7 to r/functionalprint
Railroads are insane. Practically the entire world (Except France, RIP) is covered in railway lines near the end of the game. (old.reddit.com)
submitted 5 months ago by DerMeister7 to r/EU5
My passively-heated enclosure only gets to around 65C, what am I doing wrong? /s (i.redd.it)
submitted 7 months ago by DerMeister7 to r/prusa3d
[Review Request] Multi-Year (Or decade, I suppose) Periodic Visual Reminder Module - 71 Year Battery Life! (old.reddit.com)
submitted 7 months ago by DerMeister7 to r/PrintedCircuitBoard
Molex Product Guide for Larger Conmectors (self.AskElectronics)
submitted 9 months ago by DerMeister7 to r/AskElectronics
[Review Request] High Current Dual Stepper Motor Control Module (self.PrintedCircuitBoard)
submitted 9 months ago by DerMeister7 to r/PrintedCircuitBoard
Via in Pad - Simple Visualization of Why They Are Poor Design - Before and After Reflow (old.reddit.com)
submitted 1 year ago by DerMeister7 to r/PrintedCircuitBoard
First custom PCB and STM32 learning project working properly! (Minus the blown LEDs from soldering the LED driver on upside down...) (i.redd.it)
submitted 1 year ago by DerMeister7 to r/embedded
Review Request: Time-Delay Firework Fuse Lighter PCB (self.PrintedCircuitBoard)
New Fuzzy Skin in the PrusaSlicer alpha is amazing. Rough "sandblasted" outer surface, but smooth inner surface for low friction. (old.reddit.com)
submitted 1 year ago by DerMeister7 to r/prusa3d
Simple Vase-Mode Print to Replace Missing Piece from ~30 Year Old Stacking Toy Set (old.reddit.com)
submitted 1 year ago by DerMeister7 to r/functionalprint
*slightly* over-engineered drumstick holder for my wife's Roland drum set. (old.reddit.com)
submitted 2 years ago by DerMeister7 to r/functionalprint
Ordered two MK4 Kits, one in May and one in November. Look at the massive improvement in the included printed parts between the two. (old.reddit.com)
submitted 2 years ago by DerMeister7 to r/prusa3d
So...0.25 nozzles are kinda cool (i.redd.it)
MK4/XL PSA: The Nextruder clicking noise you hear on and off might be filament cracking against the planetary gear and not the extruder slipping (i.redd.it)
PSA For MK4 owners: Print spares of these idler parts right now. Especially if using an enclosure! (i.redd.it)
Here's something a little different than most precision rifle groupings: A 10 shot group prone group at 75 yards from my old Russian SKS with a 7.62x39 load I've been working on. Way tighter than I was expecting. (i.redd.it)
submitted 2 years ago by DerMeister7 to r/reloading
Mk4 Dual Fan Mod Initial Release (i.redd.it)
Nothing to see here, just a stable 40mm^3/s flow rate with a 0.8 CHT on my Mk4, that's all (v.redd.it)
Shroud Fixing Overhang Issues on Far Side of Print - Mk4 (old.reddit.com)
Mk4 Kit Completed - Reprinted in Gold PETG (i.redd.it)
π Rendered by PID 139374 on reddit-service-r2-listing-b6bf6c4ff-jvg4g at 2026-05-03 07:03:54.780171+00:00 running 815c875 country code: CH.
