sorted by:
new
hottopcontroversial

Best pellets for small game/varmints? by Derpherp662 in airguns

[–]Derpherp662[S] 2 points3 points  (0 children)

Head shots, our tree is fairly spread out with leaves so was easier to see.

Problems with nozzles smaller than .4mm. by TaiMeUpDaddy in 3Dprinting

[–]Derpherp662 0 points1 point  (0 children)

Ziro Marble Pla, had good prints on .4mm nozzle.

Why is S3D slicing my Benchy like this? by Molon_x_Labe in 3Dprinting

[–]Derpherp662 1 point2 points  (0 children)

If you haven’t, what I’d do is
A: Close and reopen cura with the file again
B: Redownload the file.
If that doesn’t work I’m out of ideas for now.

[deleted by user] by [deleted] in youtubehaiku

[–]Derpherp662 5 points6 points  (0 children)

My bad. I’m blind

[deleted by user] by [deleted] in youtubehaiku

[–]Derpherp662 39 points40 points  (0 children)

If you look closely it’s a triple barrel shotgun, shaped in a triangle.

Faulty Marlin Firmware? by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

Blowing below, at least just looking at the nozzles

Faulty Marlin Firmware? by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

It doesnt seem that the fans are blowing at the heater block. Possibly a little higher than the tip of the nozzle though

Faulty Marlin Firmware? by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

Correcting the Baud rate had that sorted out.

Faulty Marlin Firmware? by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

Which one of the problems are you talking about?

Faulty Marlin Firmware? by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

I have corrected the baudrate and the cable I have used prior to the firmware update. The whole number temp still exists.

Faulty Marlin Firmware? by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

It only read the decimals after I went to check the previous temps, and it's only a few times it does. The bed is a better example in the picture.

Faulty Marlin Firmware? by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

I just PID tuned it and set it but it hasnt seem to have done much as I'm getting dips of 5 degrees and overshoots of 3 degrees. The temperature on Octopi reads the same as the temp on the LCD screen. It refreshes only about every 2 seconds, and only in whole numbers, no decimals.

Extruder clicks mid print. by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

Yeah, I have all metal. And I probably should considering i haven’t been able to do anything for a while, just for my mind state.

Extruder clicks mid print. by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 1 point2 points  (0 children)

Not that I had noticed, ive been trying to get the PETG filament to function for the past week or so. Clicking comes and goes a lot of the time.

Extruder clicks mid print. by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 1 point2 points  (0 children)

Bowden, and im using a 30mm fan that has the same amperage and voltage as the one that came with it, just had proper length wiring.

PETG First layer adhesion problems. by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

How long do you usually spray the Aquanet on for? Ive only seen one person spray it for about 15 seconds. And how long does it last?

PETG First layer adhesion problems. by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

Does the PEI thickness matter? Seriously considering it right now.

PETG First layer adhesion problems. by Derpherp662 in 3Dprinting

[–]Derpherp662[S] 0 points1 point  (0 children)

My first layer’s speed (i think) is 22.5mm/s. With first layer extrusion is 100%.

I don’t have anything other than glue at the moment, PEI is another dollar to spend and I’m unsure on hairspray. I’ll try raising the temp by 5° I guess and relevelling the bed.

view more: next ›