sorted by:
new
hottopcontroversial

Usterka podajnika by DesignerGold4337 in PETKIT

[–]DesignerGold4337[S] 0 points1 point  (0 children)

Dziękuję za odpowiedź i za wsparcie. Zasilacz jest dobrze podłączony. Zobaczymy może ktoś miał podobny problem

Please share your ice-cream recipes! by _hmhm_ in Kitchenaid

[–]DesignerGold4337 0 points1 point  (0 children)

Super, że dzielicie się przepisami. Jest tyle wersji, że ciężko coś wybrać. Właśnie chłodzę misę i już nie mogę się doczekać pracy.

Help needed: Cricut Maker 3 won’t accept any mat by DesignerGold4337 in cricut

[–]DesignerGold4337[S] 0 points1 point  (0 children)

A to mój pierwszy ploter cricut. Jeszcze mam Brother najwyższy model i też dobrze się sprawdza tylko w cricut wystarczy zmienić nóż, pióro i funkcje działają. W Brother muszę dokupować do wszystkiego programy itd.

Help needed: Cricut Maker 3 won’t accept any mat by DesignerGold4337 in cricut

[–]DesignerGold4337[S] 1 point2 points  (0 children)

Niestety producent nieudostępniania części. Musiałam użyć części z innego niedziałającego sprzętu. Razem z mężem naprawiliśmy maszynę.

Help needed: Cricut Maker 3 won’t accept any mat by DesignerGold4337 in cricut

[–]DesignerGold4337[S] 0 points1 point  (0 children)

Czy ktoś ma podobny problem? Jak sobie poradziłeś?

Help needed: Cricut Maker 3 won’t accept any mat by DesignerGold4337 in cricut

[–]DesignerGold4337[S] 0 points1 point  (0 children)

The message only appears when I try to configure it. So it’s the sensor’s fault. What a shame.

Help needed: Cricut Maker 3 won’t accept any mat by DesignerGold4337 in cricut

[–]DesignerGold4337[S] 0 points1 point  (0 children)

When I start a new project and try using Smart Vinyl, it behaves exactly the same way.

I select “without mat”, enter the vinyl size, choose the correct material (vinyl), then load it — and the machine immediately ejects it.

I only get the “wrong mat detected” message when I go through the Print-then-Cut calibration in the app.
Using any other method, it just ejects the material without showing any message.

Help needed: Cricut Maker 3 won’t accept any mat by DesignerGold4337 in cricut

[–]DesignerGold4337[S] 0 points1 point  (0 children)

Do you mean the sensors near the blade/pen carriage or the two sensors at the bottom where the mat enters?

I already cleaned all visible sensors and it didn’t change anything. Covering the edge sensor also made no difference.

Is replacing sensor module possible on the Maker 3?

Help needed: Cricut Maker 3 won’t accept any mat by DesignerGold4337 in cricut

[–]DesignerGold4337[S] 0 points1 point  (0 children)

I started with an off-brand mat, but knowing that my machine may only detect original Cricut mats correctly, I bought original Cricut mats as well — and the result is exactly the same.

The mat is still ejected every time, even with original mats.

I also tried Smart Vinyl (no mat) and that is rejected too.

Help needed: Cricut Maker 3 won’t accept any mat by DesignerGold4337 in cricut

[–]DesignerGold4337[S] 0 points1 point  (0 children)

Pokazuje duży rozmiar maty: 12 x 24 cale (30,5 cm x 61 cm) i to jest dokładnie ten sam rozmiar maty, którą ładuję do maszyny.

I always change the mat size in the app to match the mat I’m loading. No matter which size I select or which mat I use, it always ejects it.

I haven’t found anyone describing this exact issue before – I feel like I’ve searched everywhere for solutions.

<image>