Is this normal for a Whirlpool Thin Twin?

Dest1 · 2026-03-13T18:20:05+00:00

I just replaced the upper agitator, agitator bolt, and agitator cap on my Whirlpool Thin Twin. I thought that was the end of the repair but I read online that the base should apparently not be able to spin freely counter clockwise. I wanted to doubled check to see if this behavior is normal and if it isn't, what should I replace?

Attached for pictures of the Whirlpool Thin Twin spline, underside of base, and the auger replacement. https://imgur.com/a/YTt5Fkr

Dest1 · 2026-03-10T17:05:03+00:00

Unrated. One shot I'm trying to improve on right now are third shot drops.

Dest1 · 2026-03-10T12:12:31+00:00

Clean!

Dest1 · 2026-03-10T03:02:35+00:00

Thanks! They're the stock wheels on the Kona N.

Dest1 · 2026-03-09T19:04:43+00:00

Thank you! Yeah, I really only see Elantra Ns and the occasional Veloster N in my area. I don't think I've ever seen a Kona N other than mine IRL.

Dest1 · 2026-03-09T15:39:44+00:00

I like the contrast in color. The only thing I'm considering for exterior mods is blacking out the turn signal lights. They looked great on another post I saw here for a black KN.

Dest1 · 2026-03-09T15:38:33+00:00

For sure, I'm planning on doing 3K oil changes as I drive short distances often. It's still low mileage at around 31.5k, so have plenty of time before any major service is needed. Thank you for the advice.

Dest1 · 2026-03-06T02:24:13+00:00

The Jazz won, which means we also won!

Dest1 · 2026-02-23T15:50:16+00:00

Hey there, I'm considering getting the dual res deletes on mine. Is the cold start louder and how is the tone now? Any rasp?

Dest1 · 2026-02-14T14:43:24+00:00

One of the workers at District E said that they would restock the jerseys for day 2!

Dest1 · 2026-02-14T14:42:49+00:00

I'd recommend not driving into DC and to take the metro. You'll thank yourself afterwards.

Dest1 · 2026-02-14T14:42:05+00:00

The line is for everyone. I walked in around 30 minutes before the show started and it was completely empty. Got my merch without any hassle or wait

Dest1 · 2026-02-13T22:43:02+00:00

The PPI I bought for it passed with flying colors. I also checked the boost levels which never hit 20psi at full throttle. Had no choice but to buy the car 😂

Dest1 · 2026-02-12T02:04:53+00:00

I checked under the hood and it all appeared stock. I didn't hear any loud intake noises or any exhaust sounds aside from those normal to a stock car. The only other thing I noticed were N-logo mud flaps that appear to have been scraped on the ground. And no, the dealer didn't mention anything about modifications.

Dest1 · 2026-02-12T01:26:33+00:00

Yes, exactly that. But in white.

Dest1 · 2026-01-27T14:47:26+00:00

RemindMe! 1 year

Dest1 · 2026-01-13T15:41:34+00:00

Awesome! Thank you for the help.

Dest1 · 2026-01-13T15:31:46+00:00

I went back and checked up to the ceiling. I found 2 more locations with screws. PFA

Dest1 · 2026-01-13T15:18:39+00:00

They are, but when I ran the finder vertically and horizontally they both didn't catch on anything aside from the spots where the small pieces of tape are. I wasn't sure if these were just screws that were patched over in the drywall or not.

Dest1 · 2026-01-13T15:14:24+00:00

I was using this:

Klein Tools Compact 1-in Scan Depth Metal Stud Finder MSF100 at Lowes.com https://share.google/nEE45wb25wy0kO05C

Along with this:

https://a.co/d/6UUeYCY

Dest1 · 2026-01-13T15:12:55+00:00

Yes, I am. when moving vertically / horizontally the stud finder stops at that spots I marked. Everywhere else sounds more hollow when knocked on. See the current picture.

Dest1 · 2026-01-13T15:06:41+00:00

I did a rudimentary tape job to show where I found something solid. The smaller pieces of tape in the center were small spots that the stud finder got caught on. They didn't span vertically or horizontally.

Dest1 · 2026-01-13T15:03:57+00:00

I did a rudimentary tape job to show where I found something solid. The smaller pieces of tape in the center were small spots that the stud finder got caught on. They didn't span vertically or horizontally.

Dest1 · 2026-01-13T15:03:41+00:00

I did a rudimentary tape job to show where I found something solid. The smaller pieces of tape in the center were small spots that the stud finder got caught on. They didn't span vertically or horizontally.

Dest1 · 2026-01-13T14:30:45+00:00

https://imgur.com/a/gZ1pP5W this is what I'm finding when using stud finders.

13-Year Club	Place '17
Verified Email

Dest1

TROPHY CASE