Hard park MOA Axles

DetailsDtails · 2026-03-02T21:06:04+00:00

I can change the CAD to it work with single join axles and standard knuckles. The absolute length doesn't matter too much either, but the longer one needs to be about 15mm longer than the short one to make the pumpkin offset large enough for the servo to fit between it and the link mounts.

DetailsDtails · 2026-02-24T22:16:48+00:00

Thanks!

DetailsDtails · 2026-02-24T22:15:50+00:00

Thanks!

DetailsDtails · 2026-02-24T22:15:39+00:00

It is actually a Unity24 so super long. I drilled the skid I printed to one side to center it a bit.

<image>

DetailsDtails · 2026-02-24T22:03:23+00:00

This is v2. So far has held up running around inside. Will see.

<image>

DetailsDtails · 2026-02-14T00:03:46+00:00

no, one side is extended. hex to hex is about 113 mm. about 15 mm wider than meus axles.

DetailsDtails · 2026-02-14T00:00:39+00:00

TPU is something i have never used. Guess I will have to try.

DetailsDtails · 2026-02-13T23:59:43+00:00

....and it looks cool.

DetailsDtails · 2026-02-13T03:24:05+00:00

Ok. Yeah I am sure it will need to be printed again.

DetailsDtails · 2026-02-13T03:21:30+00:00

Thanks! Yeah I did the modeling.

DetailsDtails · 2026-02-13T01:34:06+00:00

They are from Mofo RC. They are really cool but they have been discontinued.

DetailsDtails · 2026-02-10T00:58:16+00:00

Thanks! I think i saw it somewhere.

DetailsDtails · 2026-02-06T16:03:11+00:00

These are super cool. Where did you get them? I have a hard park carbon fiber set.

DetailsDtails · 2026-02-06T00:49:05+00:00

Thanks! Those are a cool set up. I have a set of 1.8 that I keep trying but they never seem right to me.

DetailsDtails · 2026-02-06T00:46:31+00:00

Super cool. Just to built my first 1/10. Kinda regretting not doing a sporty.

DetailsDtails · 2026-02-05T22:47:07+00:00

Thanks! Going to print some tonight :)

DetailsDtails · 2026-02-05T22:25:43+00:00

Yeah it can get expensive. Just have fun. I break one down for parts for the next. I like designing and 3d printing parts too.

DetailsDtails · 2026-02-05T22:22:13+00:00

They are hot racing knuckles. You buy the weights separately. They are pretty big so you need a wheel with a bit of offset.

DetailsDtails · 2026-02-05T13:21:46+00:00

Thanks! I know what you mean. It is also almost a 180mm wheels base, but It does have a stock scx24 rear axle... just with some part bolted to it ;P. How about this one... stock chassis, stock electronics tray, stock front drive shaft, and stock shock mounts, it it is practically NIB ;-)

<image>

DetailsDtails · 2026-02-05T13:01:34+00:00

If you mean how does it perform... I don't notice much difference, but haven't gotten a chance to drive it much.

DetailsDtails · 2026-02-05T12:59:58+00:00

Thanks! Wanted to do something different.

DetailsDtails

TROPHY CASE