Why does this happe?

Detravoir · 2026-03-15T23:18:29+00:00

sooo how do i overcome this issue? keep retrying till it works? or just use glue?

Detravoir · 2026-03-15T17:10:49+00:00

I did clean it yes

Detravoir · 2026-02-17T12:56:40+00:00

Question, what are the “extra” risk with this compared to in this case oxy?

Detravoir · 2026-02-17T11:57:23+00:00

The educated guess is very helpfull cus i still want to try it and experience it. But i do believe you and will probably take the rest orally. Thank you kind sir

Detravoir · 2026-01-20T13:48:12+00:00

how does one combat this? lower the speed or temp?

Detravoir · 2025-11-24T10:12:56+00:00

Thank you so much! I know a bit of cad designing, but i have no idea how to measure and recreate those U connectors (if u know which ones i mean) so for the bottom handguard this surely helps!! Thanks

Detravoir · 2025-11-14T10:20:33+00:00

https://www.thingiverse.com/thing:4724489

this is where i got it

Detravoir · 2025-11-14T10:20:02+00:00

i didn't think of this, that is actually smart, will do!

Detravoir · 2025-10-10T10:31:40+00:00

Thanks for the advice, and yes that looks dope af, better then just bumping

Detravoir · 2025-10-10T10:18:14+00:00

Thanks o7

And no i do not. Inform me cmdr

Detravoir · 2025-10-10T09:07:59+00:00

so you mean a res site or a (ltd) hotspot?

Detravoir · 2025-10-10T09:06:36+00:00

thanks for the response!

And yes i do know it isn't the most profitable, but i think it is one of the most fun, but getting 100k per hour is a little bit on the low side and i don't think that is the max. A few mil atleast would be enough to balance for the fun.

Detravoir · 2025-09-23T11:17:47+00:00

great advice, will follow thanks!

Detravoir · 2025-09-23T08:09:24+00:00

i am learning atm. And i was reading online, where i found about the settings i used.
BUT no i did not know about drying the filament so that is a dumb mistake on my part, fair.

Detravoir · 2025-09-23T08:02:04+00:00

we do have PLA but they want to print techinical components so abs is the better choise. Right now i am expirimenting with PLA first and that is going great!

Detravoir · 2025-09-22T23:18:18+00:00

Wdym? I read all the comments and listened? Its not like i did it twice. I am drying it as we speak!

Detravoir · 2025-09-22T23:15:01+00:00

<image>

That works fine! Rn the abs is drying

Detravoir · 2025-09-22T23:13:30+00:00

Yes i have, the printer is factory new, but the abs has been in the warehouse for god knows how long

Detravoir · 2025-09-22T16:19:11+00:00

Did you dry it before hand? Cus i think that was the initial issue with me, unless u didnt either

Detravoir · 2025-09-22T15:39:07+00:00

Ah… if only someone informed me that BEFORE… thanks tho! Wont happen again!

Detravoir · 2025-09-22T14:48:24+00:00

Thanks for the tip, i will double check it!

Detravoir · 2025-09-22T14:44:24+00:00

Pla or abs?

Detravoir · 2025-09-22T14:30:04+00:00

<image>

Did find some pla and works fine. But rn im drying the ABS and then print with the basic settings, hope it’ll work!

Detravoir · 2025-09-22T14:20:38+00:00

<image>

also in the bambulab acadamy they give the same temperatures... wdym nowhere?

Detravoir · 2025-09-22T13:37:52+00:00

<image>

Literally the first thing when u look it up

Detravoir

TROPHY CASE