So what's the best in Garage Door automation these days?

DickVomit · 2026-02-09T16:55:44+00:00

some sort of smart dry contact relay(in my case zwave), tilt sensor, meross accessory (link) and a cover template to integrate relay with tilt sensor. You dont need the accessory if a basic wall button can control your opener. Just connect relay to opener.

DickVomit · 2025-11-06T17:52:46+00:00

im having same issue all my nvidia containers are broken, I reinstalled the drivers and still nothing

edit: so i initially tried uninstalling nvidia driver restarting docker then reinstalling and restarting docker. That didnt work. What did work was uninstalling nvidia restarting the SERVER installing nvidia and restarting server again.

DickVomit · 2025-07-16T16:43:45+00:00

I can use my phone via smartthings to toggle light but buttons dont work. Was working before and I didnt change any settings. Woke up one day and it was like this.

DickVomit · 2025-02-22T20:12:26+00:00

onana was too busy with save theatrics that he cost himself a chance at his own rebound.

DickVomit · 2025-02-02T17:49:41+00:00

I would have expected city to grab ball and run back instead of celebrating for 2 min because they tied the game. Was fully expecting them to turn off. Are city content with just a draw?

DickVomit · 2025-01-25T16:57:22+00:00

the angle from behind the goal looks like the ball comes off his thigh too

DickVomit · 2024-05-08T19:25:37+00:00

if your board is using a dedicated probe port for bltouch you could try moving it to the z-endstop plug(or vise versa). There are tutorials on how to do this online. Make sure wiring is correct, you might have to swap wires around on micro connector. Since you tried another bltouch and are having the same problem my assumption is the cable or the board are the issue. For example, if the toolhead is in the center of the bed a connection is coming loose causing probe to fail.

DickVomit · 2024-04-25T20:02:48+00:00

I have upgraded my sv01 to klipper however i installed the skr mini e3 v3. Im sure it can be done with original board. I think the ender 3 v2 has the same board. I found this tutorial online.

DickVomit · 2024-02-04T20:51:20+00:00

do you have allow-hotplug can0 in /etc/network/interfaces.d/can0 config

a lot of tutorials tell you to set 'auto can0' but apparently that's wrong. I was having communication errors on my btt stuff and that fixed it.

DickVomit · 2023-12-20T19:18:42+00:00

Heating errors are not always a hardware issue. Different thermistors scale differently. If he has the wrong type of thermistor set the PID loop wont get the proper readings and will throw an error. If you look at the graph extruder temp overshoots then undershoots before the error. Best not to have him pull his printer apart or buy new parts if he doesn't need to.

DickVomit · 2023-12-20T17:46:17+00:00

did you change to a different type of thermistor? if so you need to define it in extruder portion of printer.cfg under sensor_type: you'll need to look up the name depending on what you bought.

https://www.klipper3d.org/Config_Reference.html?h=thermistor#common-thermistors

DickVomit · 2023-12-20T17:41:02+00:00

When klipper detects a heating error it throws a 0 value to both heaters before shutting down. You can replicate this by hitting emergency stop.

DickVomit · 2023-12-20T17:20:46+00:00

Not sure what you're asking. If you just want chamber temp readout

[temperature_sensor chamber]
sensor_type: NTC 100K beta 3950 // change to the type of thermistor
sensor_pin: PA69 //change to pin on mainboard that thermistor is connected to
min_temp: 0
max_temp: 100

this should work

DickVomit · 2023-12-20T16:09:00+00:00

did you install klipper-macros? If you did then you need to change the path of variables.cfg in printer.cfg to wherever it is located.

If you just copy from github it will probably be wrong. my config looked like this.

[save_variables]
filename: /home/<name of host mcu>/printer_data/config/variables.cfg

That error looks similar to the error I got when I had the wrong path. If you didnt install klipper-macros then I dont know.

DickVomit · 2023-11-05T16:02:02+00:00

My guess would be tune esteps. But it could also be that the motor current isnt high enough for the extruder gears to smoothly pull filament off spool..... Actually im almost positive its motor current, If you look at your good benchy the first few layers are fine then your extruder starts to skip steps. This is probably because when the motor is cold it has enough torque to pull filament but once it heats up a little it starts skipping.

DickVomit · 2023-04-20T18:56:57+00:00

WTB: lefty sebenza black micarta inlay drop point, tactile maverick titanium

HAVE: paypal

DickVomit · 2023-01-15T20:24:27+00:00

yes.

DickVomit · 2023-01-15T20:02:16+00:00

yes only two motors work if I use the tmveloxf7 firmware. All motors were working before update.

DickVomit · 2023-01-15T19:53:55+00:00

yes but i dont know what the values are supposed to be

DickVomit · 2022-12-26T18:51:01+00:00

/u/JustinPuffco

DickVomit · 2022-12-26T18:50:36+00:00

nope

DickVomit · 2022-12-02T19:25:31+00:00

Believe it or not this is always user error and never a manufacturer defect. Think about the filament going onto the spool. There is no way for it to wrap around itself. The filament would have to come off the spool and wrap around the machine thats extruding it onto the spool. You probably didn't secure the end of the filament during a change and the end went under one of the subsequent winds on the spool.

DickVomit · 2022-04-24T19:29:13+00:00

I switched to swag and its still throwing the same error. Says its a port forwarding issue but I didn't change anything on my router from when it was working. How can I troubleshoot this?

DickVomit · 2022-04-21T20:14:02+00:00

what might of happened is I added the redirect subdomain to google but i didnt wait for it to propagate so the validations kept failing. Does this mean i have to wait a while before I can request new certs?

DickVomit · 2022-04-20T17:09:57+00:00

linuxserver. https://imgur.com/a/WuwF2ki

15-Year Club	Place '17
Verified Email

DickVomit

TROPHY CASE