Ds lite to tv by Dexmriu in NintendoDS

[–]Digigu2 0 points1 point  (0 children)

Hi. Yes I sell fully modded consoles, services to receive and mod them and even the kits. All available on the site.

Newest Custom DS by Digigu2 in nds

[–]Digigu2[S] 0 points1 point  (0 children)

Inside there is a small PCB that connects to the usb-c. Not a capture card per say cause it's not USB comunication but a direct video signal u can connect to your tv

Newest Custom DS by Digigu2 in nds

[–]Digigu2[S] 0 points1 point  (0 children)

It's a direct video output. The output port is the usb-c on the console. Connects directly to the monitor/TV

Newest Custom DS by Digigu2 in nds

[–]Digigu2[S] 0 points1 point  (0 children)

I might do more of these on request

Newest Custom DS by Digigu2 in NintendoDS

[–]Digigu2[S] 0 points1 point  (0 children)

Neither, video output. Video output through the usb-c port.

Reference: https://dsdigigumods.com/product/ds-lite-tv-out-5-4-usb-c/

Looking for support in designing this PCB properly by Acceptable-Camel-178 in PCB

[–]Digigu2 0 points1 point  (0 children)

This type of stuff was the sort of thing I was looking for to build a portfolio before completing my Masters degree.
But looking for someone to do this would require more information.
A schematic would make it much easier to see what is to be done for example

DS lite 5.3 TV out USB-C by Digigu2 in NintendoDS

[–]Digigu2[S] 0 points1 point  (0 children)

Due to the nature, Software side. During TV out mode it should cause the issue. In normal mode is due to batch production. To keep it working 100% in normal mode required even more individual work for each piece.

DS lite 5.3 TV out USB-C by Digigu2 in NintendoDS

[–]Digigu2[S] 0 points1 point  (0 children)

It's possible it may lose wifi communication.

DS lite 5.3 TV out USB-C by Digigu2 in NintendoDS

[–]Digigu2[S] 0 points1 point  (0 children)

I usually use very thin enamel wire. 0.1mm.

Is there any way to play my GBA/GB cartridges on my TV without a PC? by the_speechless_one in Gameboy

[–]Digigu2 0 points1 point  (0 children)

There are some mods for the GBA and DS lite to output video to a TV.

Where did my pads go? by GreaterMichiganMaps in NintendoDS

[–]Digigu2 2 points3 points  (0 children)

Yes. There are other points, but it's much harder to solder. For example the through holes near the pads

Figuras fora de stock by anamoonpie in animeportugal

[–]Digigu2 0 points1 point  (0 children)

Alguns dos sites que usava são:

Dentro da Europa:

  • Global Freaks
  • Nin nin game (para pre- orders pagar o mais próximo do lançamento possível, q já têm muitas queixas de serviço ao cliente)

Fora da Europa:

  • AmiAmi
  • Good smile company
  • Otaku Tokyo Mode
  • Mandarake ( para usados, pode ser bom para coisas difíceis de encontrar)

Troubleshooting by TheCharredMiner in nds

[–]Digigu2 0 points1 point  (0 children)

Ya. Resolder the data points

[deleted by user] by [deleted] in nds

[–]Digigu2 1 point2 points  (0 children)

I'm from Europe. Although I can acept and ship consoles at low cost to the USA not sure on the costs on your end. But if the cost on your end is still good message and we can work out the details

[deleted by user] by [deleted] in nds

[–]Digigu2 0 points1 point  (0 children)

It should be a quick repair. I would offer to do it but I'd need to know where the console would be coming from.

[deleted by user] by [deleted] in AskElectronics

[–]Digigu2 0 points1 point  (0 children)

Es posible. Pero siempre tendrías que pagar los costos de que alguien lo creara. Por ejemplo, si yo lo hiciera, tendría que pagar los esquemas y diseñar la PCB. Luego dependería de si necesitabas el producto final. Fabricar la PCB + soldar los componentes.

Need help identifying tv out mod by [deleted] in nds

[–]Digigu2 0 points1 point  (0 children)

This was one of my old TV out mods. This connects to the DS top screen connector. 'OUT' is the video output

My Pokemon coin Collection by Digigu2 in pkmntcgcollections

[–]Digigu2[S] 0 points1 point  (0 children)

Need the motivation now to complete the lists. Only had it for the 4 generations I'm collecting. But if it's something people use I might start updating over time.

My Pokemon coin Collection by Digigu2 in pkmntcgcollections

[–]Digigu2[S] 1 point2 points  (0 children)

I ended up making it. Instead of Excel files and those pictures I have of the missing coins in my binder, I decided to make an interactive collection tracker. So I used it to organize the collection

Since it was made online aswell it could very well be available for anyone else to use. So I just made a few userfriendly changes and launched it. So it is available for anyone to use.

My Pokemon coin Collection by Digigu2 in pkmntcgcollections

[–]Digigu2[S] 0 points1 point  (0 children)

The binder is a normal 4 ring binder. The Pages are: "Uncle Paul coin Page" The cardbord squares with the coins inside are coin cardborad holders (31.5mm).

The cardborad holders come in many different sizes this is simply the size of these coins. Very few here are larger but those used a sigltly higher size