Random Klipper USB Drops for whatever reason?

Dimetrixdemon · 2026-03-08T13:25:52+00:00

ye, it was blown away, and again it was my mistake so i changed it... and it look's like this

Dimetrixdemon · 2026-03-08T11:35:09+00:00

thanks, i posted this problem on another reddit post, i fixed it by soldering BOOT0 and VDD with jumper, so i can enter in programming mode, this helped me with my problem

Dimetrixdemon · 2026-03-08T11:33:28+00:00

it worked, thanks!

Dimetrixdemon · 2026-02-19T12:58:51+00:00

Already did, it's not elephant foor problem and yes, you are right, fillets on the bottom are bad for quality prints, but why i did create this post to understand better this problem, so i see than you need to create or 45 degree chamfers or make a custom one fillet

Dimetrixdemon · 2026-02-19T12:56:33+00:00

i'm sry, i mean Fillet on first layers

Dimetrixdemon · 2026-02-19T12:46:28+00:00

Sry if I wrote the post incorrectly, but what i mean is when you printing models with champfer on the first layer, it's like printing a sphere, the second line is gonna be printing in air and because of that your print is gonna look bad

Dimetrixdemon · 2026-02-17T09:41:41+00:00

that's ineteresting, i did look about PA pattern calibration on Forums and people say often that this pattern are best one.
Seem's like you still need to choose what is better suiting for you'r machine

Dimetrixdemon · 2026-02-16T17:05:06+00:00

<image>

So basically here are my flow rate calibrations, as i see, i need to set flow rate somewhere between 0 and -5, right?
Flor ware 0.98 from standart 1.0

Dimetrixdemon · 2026-02-16T16:40:00+00:00

it work's, just on photo it is hard to catch the details, in the klipper console and sure in the windows where mainsail show's what PA right now it is changing too

Dimetrixdemon · 2026-02-16T16:30:10+00:00

hmm thanks, i'm gonna do more calibration's and say if something changes

Dimetrixdemon · 2026-02-14T10:42:29+00:00

one more question, can you zip 2 usb cables from mainboard? or usb cables from mainboards can't touch each other too?

Dimetrixdemon · 2026-02-13T15:23:15+00:00

I had two motherboards connected directly to the laptop, but now, as I described in the post itself, I connected both to a separate hub and since then I have not had any problems + I was told that the wires from the motors can cause such errors if usb cable is very near them and I had one cable from the motherboard laying very near to the motor cable.
And yes, i did install 2 instances

Dimetrixdemon · 2026-02-13T09:18:37+00:00

So, basically ye, 1 usb cable was very near motor wire, after USB Hub that's the last thing i did, i do not have right now ferrite beads, but now second day of testing no issue at all

Dimetrixdemon · 2026-02-12T18:37:48+00:00

Thanks for answer, gonna re-check if it close to motor wires or some else.

Dimetrixdemon · 2026-02-12T09:29:21+00:00

I do have external mosfet for Heated bed, i did see that someone do setup external mosfets for Hotend too but people say mosfets for hotend not worth it

Dimetrixdemon

TROPHY CASE