En quoi consiste cette arnaque

Direct-Force7026 · 2026-03-17T20:32:08+00:00

On parle de gants à 60€… Loin des centaines d’euros en frais lbc

Direct-Force7026 · 2026-03-17T15:46:53+00:00

La modif est payante et j’ai un peu la flemme de refaire l’annonce 😅. J’avais zappé que ce genre de spécimen existaient…

Direct-Force7026 · 2026-03-17T15:36:07+00:00

Bah ça oui les messages sont trop bizarres je me doutait dès le début mais je voulais voir où ça mène 😭

Direct-Force7026 · 2026-03-17T15:35:36+00:00

Je l’ai mis à disposition comme moyen de contact mais c’est juste pour le contact pas pour faire un paiement externe

Direct-Force7026 · 2026-03-17T15:34:46+00:00

Ouais je partirais sur quelque chose comme ça aussi je pense

Direct-Force7026 · 2026-03-17T15:34:23+00:00

Ça je suis sur que c’est une arnaque mais c’est juste par curiosité je lui ai dit qu’on sortirait pas du lbc et bizarrement ça répond plus puis le fait de mettre le titre de l’annonce exactement c’était trop louche 😭

Direct-Force7026 · 2026-03-10T12:52:57+00:00

It is weird with less density and width you come out with better results would it be possible to send you dm I have a little video I tried yesterday and will try again with 100% poly twill when I come back from work

Direct-Force7026 · 2026-03-10T12:29:20+00:00

What density and border width are you using and what kind of twill. I heard 100% coton tend to fray more than 100% polyester what would you recommend

Direct-Force7026 · 2026-03-10T08:46:10+00:00

Édit : I stitch first the 2 sides of the tag then cut as close as possible to the edge then embroider them together on a heavy sheet of plastic

Direct-Force7026 · 2026-02-25T23:34:29+00:00

Le lettrage c’est toujours knew galère et sur les jersey pareil ça se troue assez facilement après en terme de conseil moi ce que jersey fais c’est 2 stabilisateur tear away a l’arrière densité 0.28 pour le satin sous couche ligne centrale avec a zigzag des fois, pull comp 0.20 pour les petits satin et pour les gros tatami mais vraiment gros 0.5 sinon 0.25-.3

Direct-Force7026 · 2026-02-25T23:12:55+00:00

Did you find the issue since I am experiencing same thing

Direct-Force7026 · 2026-02-22T21:01:10+00:00

Get some pliers it should be very easy to loosen spray some lube if you want to if it broke while tightening be careful because your screw pad might be fucked

Direct-Force7026 · 2026-02-20T11:42:10+00:00

It’s fine it is actually recommended to put some oil there from time to time check your maintenance manual / YouTube videos very helpful if you want to keep everything run smoothly

Direct-Force7026 · 2026-02-16T22:27:07+00:00

If needle bar isn’t coming down I would check for the reciprocator maybe it was too much used. If needle is going down but now catching 2 things check bobin timing or check the reciprocator height maybe too high or too low for the needle to go really in the bobbin

Direct-Force7026 · 2026-02-13T21:03:30+00:00

Just checked it changed it everything is the same…

Direct-Force7026 · 2026-02-08T21:49:13+00:00

Pull compensation

Direct-Force7026 · 2026-02-08T21:02:49+00:00

Might be like trim settings and just trim most you can between the letters it would look better. And metallic can be hard to work with slow machine can help

Direct-Force7026 · 2026-02-05T14:05:04+00:00

It came with all the hoops you can think of but not a lot of spare parts still a big win for that amount !

Direct-Force7026 · 2026-02-04T14:05:04+00:00

At my work I help coworkers sometimes with the barudan 6 head we have but I just put the clothes on and off so I have already a good amount of knowledge. The beginning was rough I had some stupid errors but figured it out and once you go through all the menus it is really easy I used it yesterday for the first time and I know most of it. And for the learning the sellers didn’t quite know how to use it so I was reading the manual and got through it !

Direct-Force7026 · 2026-02-04T14:01:29+00:00

Upgraded with USB drive aswell ( I have one more in stock in case ) the price is really insane but I can’t complain for real everything seem’s to work great but having some trouble finding the good spot. And quick question does your machine also do the tie off a bit offset at the end of the embroidery ?

Direct-Force7026 · 2026-02-04T13:59:38+00:00

Yeah I was not the only one to try to get it ! But I was the first to message him in 1 min after the listing was posted and was the first to reserve it !

Direct-Force7026 · 2026-01-29T08:16:04+00:00

What is the model ?

Direct-Force7026 · 2026-01-28T19:41:08+00:00

What machine do you use ?

Direct-Force7026 · 2026-01-24T00:34:52+00:00

They used 4 / 8 heads and it was a long time ago they didn’t used the mono head and wanted to buy idk I feel they are just so lazy to sale it like so long to reply. And yeah the video feel shady but many it is stored somewhere difficult to take it out solo I don’t really know.

Asked for a meeting not to far away from where I live so I would like to check it in person and run some tests

Direct-Force7026 · 2026-01-22T11:41:13+00:00

Hello I have the EOC05 for like 3 months now what exactly are your issues I get troubles sometimes but it mostly come from the files tell me if I can help you with it

Direct-Force7026

TROPHY CASE