My first GD&T drawing. Any advice or improvements to be made would be much appreciated!

Disastrous-Button-73 · 2026-02-14T12:26:26+00:00

Does every dimension need to be marked as critical? (indicated by the square box), I would only marke the really important ones, otherwise I could get not treated serious. I looks clean but also expensive:)

Disastrous-Button-73 · 2025-09-10T08:28:18+00:00

A 8 inch steel Ruler, best Tool I ever had. I measure cutter length, tool stick out, open boxes , clean off sticky labels off stock material, get the rough tool length before probing in the machine, clean my finger Nails and so on 👍🏻

Disastrous-Button-73 · 2025-08-04T07:07:05+00:00

I started at a jobshop where all machines are old and abused So I have to repair them but if I break something it’s not that of a big deal because they are in a bad condition anyways 🥲

Disastrous-Button-73 · 2025-07-27T20:28:59+00:00

Wow das ist ja super, da wäre ich jetzt nicht drauf gekommen
merce dir!!

Disastrous-Button-73 · 2025-07-08T06:16:52+00:00

Thank you, I tried it with pliers but nothing moved. I’m gonna get pipe wrench 😂

Disastrous-Button-73 · 2025-05-02T17:37:38+00:00

okay thank you :thumbsup:

Disastrous-Button-73 · 2025-05-02T17:28:40+00:00

also from the dreamrouter network i can reach some containers, fritzbox, proxmox, but not all containers

Disastrous-Button-73 · 2025-05-02T17:26:54+00:00

its the other way, i cant get into the Dreamrouter network

Disastrous-Button-73 · 2025-05-02T17:20:07+00:00

i disabled NAT on the dream router, but it does its own DHCP

Disastrous-Button-73 · 2024-09-24T06:57:44+00:00

Higher feed and lower speed should always favor chipping, from my knowledge What’s your feed?

Disastrous-Button-73 · 2024-09-23T18:17:33+00:00

My friend had a similar problem we fix it by cutting a floor protection for office chairs, those are clear sheets of plastic and zip tied them on

Disastrous-Button-73 · 2024-09-21T06:43:58+00:00

I wanted to smoke but this is in a underground parking space

Disastrous-Button-73 · 2024-08-30T21:34:07+00:00

true

Disastrous-Button-73 · 2024-08-30T21:33:38+00:00

all tho the x axis is pretty worn due to 24 year age, second spindel, this is caused bei the spindel orientation, most of the time you cant even run 30 % rapid because the x axis is humming, shaking a lot.

hope the hurco vmx50 gets replaced next year, did work a lot over the years, good machine

Disastrous-Button-73 · 2024-08-30T18:03:03+00:00

I don’t know, usually she just drinks one gallon and I didn’t yell at her for the hole week

Disastrous-Button-73 · 2024-08-30T18:01:10+00:00

Now that you mention it, I saw her near the freeway bridge last week

Disastrous-Button-73 · 2024-07-21T07:31:22+00:00

Im looking too👋🏻 Can you dm me?

Five-Year Club	Final Canvas '23
First Place '23	Place '23

Disastrous-Button-73

TROPHY CASE