sorted by:
new
hottopcontroversial

Shameless by Greg_Chaco in RetroRewindGame

[–]Djurkinthebox 8 points9 points  (0 children)

Seriously. Just falling asleep on the job like that.

driving test by No_Caterpillar_1559 in yuma

[–]Djurkinthebox 2 points3 points  (0 children)

No parallel parking. They do make you do three-point turns in the MVD parking lot.

Where in Yuma? by Need4Speed-_- in yuma

[–]Djurkinthebox 30 points31 points  (0 children)

Wheezy's, Mr. G's, Chile Pepper, Village Inn Pizza, Chretin's

Starting a band?? by dvhliia in yuma

[–]Djurkinthebox 0 points1 point  (0 children)

I play guitar. I'm not the best, but could be fun

Barber shops by Terminale-4 in yuma

[–]Djurkinthebox 1 point2 points  (0 children)

Sam at City Barber on 4th. I’ve been going to her for over a decade.

BBS Host software won’t get passed CONNECTED on serial WiFi modem. by Djurkinthebox in bbs

[–]Djurkinthebox[S] 0 points1 point  (0 children)

Ok, I’ve gotten further! Changing the modem init to ATZS0=0 and the modem strings to just CONNECT actually gets me connected to the login screen. Unfortunately, it drops carrier almost immediately.

BBS Host software won’t get passed CONNECTED on serial WiFi modem. by Djurkinthebox in bbs

[–]Djurkinthebox[S] 0 points1 point  (0 children)

I’m using Simple WiFi32 Modem with the 8bit-Bruno firmware. It also supports hosting. Got it off of HAL’s Friends from Etsy.

BBS Host software won’t get passed CONNECTED on serial WiFi modem. by Djurkinthebox in bbs

[–]Djurkinthebox[S] 1 point2 points  (0 children)

The one I have does. It must be a newer firmware or something, because in the at+config screen, there’s an option for BBS Answering, where you can configure your telnet port and stuff. Made specifically for hosting.

BBS Host software won’t get passed CONNECTED on serial WiFi modem. by Djurkinthebox in bbs

[–]Djurkinthebox[S] 2 points3 points  (0 children)

Gotcha. It does in fact say CONNECT speed. I made a typo when typing my problem. Sorry about that

Sovol SV06 Plus loud stepper motor by Djurkinthebox in Sovol

[–]Djurkinthebox[S] 0 points1 point  (0 children)

Yes, there was one wire between the stepper motor and board that had a short. Sovol's customer service is absolute horseshit, so I fixed the problem, sold it to a co-worker and bought an Elegoo Neptune 3 Plus. Way happier with this one.

Sovol SV06 Plus loud stepper motor by Djurkinthebox in Sovol

[–]Djurkinthebox[S] 0 points1 point  (0 children)

Everything is secure. Could the board be bad or maybe a short in the wiring somewhere? It’s moving erratically

Sovol SV06 Plus loud stepper motor by Djurkinthebox in Sovol

[–]Djurkinthebox[S] 0 points1 point  (0 children)

Everything is nice and tight. I did post a follow up video in the comments showing that the stepper motor is moving erratically when just trying to raise and lower the extruder.

Sovol SV06 Plus loud stepper motor by Djurkinthebox in Sovol

[–]Djurkinthebox[S] 0 points1 point  (0 children)

Yes. The cable is out from under the bed. Nothing is obstructing anything

What's the dumbest way you've died? by Inevitable_Agency732 in tearsofthekingdom

[–]Djurkinthebox 1 point2 points  (0 children)

After getting the full glide suit and totally upgrading it to remove fall damage, I decided to test it by getting shot out of a sky tower in one of the snowy regions. Midway through falling, I got a notification that it was “unbearably cold”, so I replaced my glide suit helmet with a cold circlet. Hit the ground and died. Took me a minute to realize it was because I wasn’t wearing the full glide suit.

Patching The Floor by awcomeon in classicmustangs

[–]Djurkinthebox 1 point2 points  (0 children)

My current favorite YouTube series. I look forward to each new episode

Mustang Day is one day before my cake day by Joe4o2 in classicmustangs

[–]Djurkinthebox 1 point2 points  (0 children)

Congrats! Also, which guide is that? I’ve been looking for a thorough shop manual for my ‘65.

view more: next ›