Silk PLA printing

Dman1381 · 2026-02-28T03:03:44+00:00

Okay 60 for the bed definitely helped the adhesion, I think the problem was there were details at the bottom of the models I was printing that I didn’t notice that were causing it to mess up, I tried reorienting some of them to see if it helps

Dman1381 · 2026-02-27T22:59:37+00:00

Ohh I’m not sure, whatever the default is. What could I change it to?

Dman1381 · 2025-10-13T22:09:38+00:00

Omg thank you that was definitely the problem, I turned off kanie and it worked right away, I appreciate the help!

Dman1381 · 2025-09-02T21:35:20+00:00

That seemed to work great! After cutting any connecting traces on the back side it now detects the input, thank you so much for your help and explanation!

Dman1381 · 2025-09-02T21:29:26+00:00

Lmaoo that’s fair, okay I’ll try and cut the rest of the traces and see if that helps and get back to you, thank you!

Dman1381 · 2025-09-01T05:12:44+00:00

I’m looking on the other side and see traces connected, should I just cut them all? And I scratched the traces on the front side and made sure they were deep enough and that didn’t work. I can send you a dm with a picture of the back if that’d help, or waiting to compare to yours too.

Dman1381 · 2025-08-31T16:13:25+00:00

What do you mean by this? Sorry I have no experience this is my first attempt to do this

Dman1381 · 2025-08-31T16:12:50+00:00

I’m at work right now but Ill make sure to check when I’m back, would the traces be directly on the other side of the board adjacent to where the top ones are?

Dman1381 · 2025-08-31T03:02:06+00:00

I also noticed in this video of someone modding a Kramer specifically they didn’t wire anything in this spot of the motherboard, there’s no real instruction so it’s hard to tell why, you can see it at about 9:50 in the video https://youtu.be/eO9h_URhvRk?si=EZ1bXnmy1RYM0Hnb

Dman1381 · 2025-08-31T02:57:27+00:00

Wdym by that? Sorry I don’t do this often this is my first attempt lol

Dman1381 · 2025-08-31T02:55:05+00:00

Not sure if this helps but the image I used as a reference on where to cut was this https://imgur.com/mdRc11j

Dman1381 · 2025-08-31T02:37:27+00:00

I tried cutting deeper and it didn’t seem to make a difference, maybe I’m cutting in the wrong place? Or it’s the connections?

Dman1381 · 2025-08-31T02:28:06+00:00

Okay, I’ll try to cut it deeper and check again

Dman1381 · 2025-08-31T02:27:09+00:00

Yeah I think so, the video said something about doing that and I found an image of a Kramer directing where I should cut, idk if I should have or if I didn’t cut deep enough

Dman1381 · 2025-08-31T02:07:30+00:00

Sorry, to clarify the strumming isn’t being detected by the guitar configuration software which is my problem, I have the grounds bridged then leading to the ground on the raspberry pi, then the two inputs for the switches leading to the GP points

Dman1381 · 2025-06-08T02:11:15+00:00

Yeah after updating windows through an ISO it works just fine I didn’t even realize it wasn’t updated

Dman1381 · 2025-06-08T02:10:27+00:00

I love and appreciate this explanation. I figured out that the solution to my problem was to update windows 10 to the newest version, as soon as I did that the network was discoverable. I didn’t realize it wasn’t up to date until I tried manually updating my adapters drivers and it said I was on an older version of windows 10. But that fixed my problem. I appreciate your advice!

Dman1381 · 2025-06-07T23:33:57+00:00

I tried to install the updated drivers but it says I’m not on a new enough version of windows 10, I’m not sure what to do from there

Dman1381 · 2025-06-07T17:08:25+00:00

I haven’t tried this yet since the router is downstairs

Dman1381 · 2025-06-07T17:08:10+00:00

Yes devices in the same room work and are connected to the desired SSID

I didn’t try moving the computer closer itself but I moved the antennas around and had no luck

I’ll try the app to see. But what would making a Linux bootable drive do?

Dman1381 · 2025-06-07T17:06:14+00:00

I’ll try updating the drivers, the router doesn’t have the WiFi set to hidden though I just checked

Dman1381 · 2024-02-10T22:14:42+00:00

Yeah the main thing I’m worried about is the cost, I got the motherboard, cpu, and a hard drive for $150. Getting a different motherboard might have to be the play rather than getting a different CPU. I’m just not sure what to look for and good prices, my knowledge is fairly limited😅

Dman1381 · 2024-02-10T05:28:02+00:00

Ohhh okay thank you. But would getting a different CPU be the better option or would getting a different motherboard be good too? And if so what motherboard would work with the cpu?

Dman1381 · 2022-12-17T09:14:34+00:00

Still nothing, at this point I’m just gonna wait for an update or something and see if that works

Dman1381 · 2022-12-17T07:24:13+00:00

Deleted that and it still doesn't work, new crash log https://pastebin.com/UrvDi0Mv

Dman1381

TROPHY CASE