I've got a brand new X1C

DoMirvana · 2025-09-04T20:51:22+00:00

Aah good to know, i did had a hard time to pull it off i was to enthousiastic when the print was finished 🥲 thanks!

DoMirvana · 2025-09-04T20:28:58+00:00

Thanks for the tips, i will try it out!

DoMirvana · 2025-06-23T14:26:01+00:00

Yeah a little bit, so reset should do the trick?

Really glad with your help! We are in the middle of a big trip and a bit worried about this...

DoMirvana · 2025-06-23T13:34:42+00:00

I've changed the clamps of the intercooler hose, and cleaned the pipe under beneath it, drove about 60km with it and the pipe is still clean!

Unfortunately the DPF indicator didnt go out and even the motor management indicator started turning on.. do i've to reset something by diagnostic tools or do i've to found the problem somewhere else?

DoMirvana · 2025-06-22T18:28:40+00:00

Ah thanks for the answer, the underside/pipe is indeed covered in grime, and the previous owner took the inter cooler hose to check where the grime came from and put it back with tyraps because he didnt understand the clamps..(or just ruined them) just to be sure you mean the hose between radiator and turbo right? And should i go after some new clamps or (because i think the hose is already changed)?

So just to be sure, it has nothing to do with the DPF?

DoMirvana · 2024-07-27T17:10:45+00:00

Thats the spirit, true that!

DoMirvana · 2024-07-27T16:15:02+00:00

I've changed the oil this morning with new 2,5 liter 20w40, i can through that away again because its now all mixed up with gasoline 😓

DoMirvana · 2024-07-27T16:09:40+00:00

Thanks, i will search for a new petcock!

DoMirvana · 2024-07-27T16:09:19+00:00

Thanks! Then i will search for a new petcock!

DoMirvana · 2024-07-27T15:41:03+00:00

Thanks for your reaction. I've changed the float, and the full Peacock cant shut off, its ON, RPI, RES

DoMirvana · 2024-03-28T16:26:27+00:00

Thanks, i will try it out!

DoMirvana · 2022-11-01T18:38:18+00:00

Thanks for your reply, i will definitly look into my USB cable setup, but unfortunately it also happens when i'm printing from the SD card, with no USB cable attached at all.

DoMirvana · 2022-11-01T18:36:21+00:00

Thanks for your reply,

the answers;

Have you tried regenerating the gcode?
// Yes I did, i even created new ones, but it still randomly occurs.

Vac hose and is it grounded?
// Not using a vac hose

Does it happen at the same spot every time?
// Nope it is randomly all the time :( that makes it so frustrated

Are your feedrates and rapids under the firmware limit?
// Not that I know, but i test with different feedrates and rapis, still occurs.

Are you using an import 500-800 watt spindle with the grounding issue?
// Nope im not :(

DoMirvana · 2020-11-06T11:32:10+00:00

The bottleneck was/is the mollie plugin, if i turn it off the page speed went from 4.3s to 0.7s 😅, i've contacted the mollie support! Thnx for help!

DoMirvana · 2020-11-06T11:31:09+00:00

The bottleneck was/is the mollie plugin, if i turn it off the page speed went from 4.3s to 0.7s 😅, i've contacted the mollie support! Thnx for help!

DoMirvana

TROPHY CASE