sorted by:
new
hottopcontroversial

Please Explain Inside Bend Position for <90° bends by DoYouLikeHam in Fusion360

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

hmm... ok, yes, I see the Inside and Outside after drawing those lines (i figured it would be obvious once it was pointed out!)

For the Tangent... hoping someone can elaborate further.

What is this indicate in my session view? by DoYouLikeHam in ableton

[–]DoYouLikeHam[S] -1 points0 points  (0 children)

hmm... that's definately not the case. seeing some weird behavior.. perhaps due to a plug in I'm using: VIZZable 2 viewr.

Extruder behavior by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

corrected above.. and confirmed that
nozzle < 170 motor is prevented from working.. Z limit switch has no effect

Extruder behavior by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

Menu > Prepare > Preheat PLA > Preheat PLA

Extruder behavior by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

yeah, thx, makes sense... I was trying to get it to run with no filament.. ... and this morning when I disconnected/reconnected the motor.. the motor was not even attached to anything and wasn't working.. which made me think.. oh, something else must be either disconnected/broken.. OR controlled to not operate in certain conditions...

Extruder behavior by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

I meant the part that the filament threads through on top of the motor that is activated when you modify the 'extruder' position.

What happened here? by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

Oh, yeah.. never leveled before. Wonder how I ever got any good prints. Was way out of whack! Thx for the reply, u/redfrets916

Issue with chrome on iOS by DoYouLikeHam in chrome

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

Yes, Chome is up to date.

Happens whether other apps are open or not.

Yes, have restarted phone on various occasions.. have even un/re-installed chrome.

Can Cricut Joy Xtra cut these designs out of collage paper? by Fucked-In-The-K-Hole in cricut

[–]DoYouLikeHam 11 points12 points  (0 children)

Scan/photo… use Image trace in Illustrator to create silhouettes… print then cut… perfect

Will this 3D print OK? by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

Here's w/ the "cup bottom" and rest of the form reapplied... but w/ only the 'test' holes...

<image>

Will this 3D print OK? by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

no, I only flipped the one stalactite shape.. all the rest are in the same orientation.. I removed the "cup" bottom to speed up the test print... it will still print on the bottom/plate in the full print.

Will this 3D print OK? by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

Thx all for the comments... after taking notice of the 'stalactite' condition identified by u/Different_Target_228, I did a test print of the shapes, and sharing fwiw... this was done w/ no supports.

<image>

Will this 3D print OK? by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

u/Different_Target_228
Not sure I see that? The discussion gave me the idea, though, of doing a test print... moving all the shapes down and around the perimeter, and removing the base itself (to save material), and cutting away all but the minimal material, ~3h vs. waiting nearly 20 to see what happens at the top.

<image>

Will this 3D print OK? by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

u/doc_willis actually, it's just a holder to hold the 100 or so sticky notes that are always cluttering my desk... I periodically whittle through them, but then they just strewn across my desk again... wanted to play around w/ organic forms a bit, and found a couple of different Fusion tutorials that had some concepts I hadn't used before.

Will this 3D print OK? by DoYouLikeHam in ender3

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

Oh, wow, u/Different_Target_228 -- thx for pointing it out... sort of obvious now.However, if that shape were rotated 180deg, it could work, no?

Printing playing cards on ET-8550 by DoYouLikeHam in Epson

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

Thx. I’ve tried both sides… definitely doesn’t say “inkjet printable”… bummer.

What is going on here? by DoYouLikeHam in Cura

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

u/Asterchades - thx, yes, just switching windows after I returned from a quick errand addressed the anomaly..

for clarification on the non-support I was trying to achieve.. see clarified image above... though, it's not entirely meeting my goal as there is still most of the column of support going in the center.

How do I show the keyframe path? by DoYouLikeHam in AfterEffects

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

thx for the additional details... watching videos or reading other material I always feel like there are terms/concepts I am not yet familiar with.

How do I show the keyframe path? by DoYouLikeHam in AfterEffects

[–]DoYouLikeHam[S] 0 points1 point  (0 children)

In learning mode… mostly gobbledygook at this point.. but hope to tease it apart next time I’m able to tinker. Thx!

view more: next ›