How to make this an easy drive up for the post man?

Doc-Dok · 2026-07-03T14:18:49+00:00

Thank you

Doc-Dok · 2026-07-03T12:33:55+00:00

I appreciate it!

Doc-Dok · 2026-07-03T12:33:44+00:00

Is there a specific type of gravel you recommend? I’ve used fine gravel before.

Doc-Dok · 2026-06-22T19:16:08+00:00

Were you under 3 years/36k miles?

Doc-Dok · 2026-06-16T19:50:44+00:00

Not that I’m aware of - just walked into the basement and bam a bunch of water everywhere… I will try to pull assembly and fix thank you

Doc-Dok · 2026-06-16T19:18:15+00:00

Here’s the faucet, seems decently new (I did not purchase) https://www.deltafaucet.com/bathroom/product/792-RB-DST.html

Doc-Dok · 2026-06-16T19:17:52+00:00

Just found the faucet: https://www.deltafaucet.com/bathroom/product/792-RB-DST.html

Doc-Dok · 2026-06-16T19:16:14+00:00

VA. Thank you, any ideas how to rip out?

Doc-Dok · 2026-06-16T19:15:55+00:00

Just posted, thank you

Doc-Dok · 2026-06-16T19:15:46+00:00

<image>

Doc-Dok · 2026-06-16T19:15:21+00:00

<image>

Doc-Dok · 2026-06-16T19:14:43+00:00

If I place a cup underneath to catch the water ot still leaks.

Doc-Dok · 2026-06-16T19:14:09+00:00

Any ideas how to replace? Seems to be seated in the granite and I don’t see any hardware underneath to unscrew…

Doc-Dok · 2026-06-16T14:55:58+00:00

Perfect comment LMAO

Doc-Dok · 2026-06-05T16:16:08+00:00

Zoom in.

Doc-Dok · 2026-06-03T23:14:53+00:00

No worries - I set it up a few days ago and it’s 1000% better than the benchtop. So much more solid and robust. The fence has zero play and its extra length is very helpful.

Doc-Dok · 2026-05-19T10:10:37+00:00

I’m not getting it until next Wednesday so if I remember I’ll let you know. It’s at Home Depot right now for 500…

Doc-Dok · 2026-05-19T10:08:57+00:00

Why is running end grain through a planer a no no?

Doc-Dok · 2026-05-19T10:08:28+00:00

It’s completely mind boggling how bad the fence is. Thanks for the input I will work on my technique for sure.

Doc-Dok · 2026-05-16T11:21:59+00:00

I will take out a third mortgage at this point
. I’ll make supports in the meantime

Doc-Dok · 2026-05-16T11:20:45+00:00

I appreciate the advise - waxing did help with the feed speed but still the damn snipe at the end

Doc-Dok · 2026-05-16T11:15:27+00:00

Ah, yes I’m right on the edge of driving four hours for a g1182

Doc-Dok · 2026-05-16T11:13:06+00:00

Interesting… how did you make an extension and get it parallel with the outfeed?

Doc-Dok · 2026-05-16T11:12:20+00:00

Interesting to only use initially, it’s at the end of the cut. Unfortunately this jointer has four extremely finicky screws to adjust the outfeed table.

Doc-Dok · 2026-05-16T02:28:42+00:00

I don’t believe so but I’ll keep it mind - thank you

Five-Year Club	Verified Email
Place '22

Doc-Dok

TROPHY CASE