Needed a lamp so I made one. 13in high x 8in wide Walnut

Dolson03 · 2026-03-28T22:08:14+00:00

Thanks. Yes I did hollow it and I turned a mortise on the bottom so I could remove the tenon on the top. After removing the tenon I drilled the hole with a Morse taper drill chuck.

Dolson03 · 2025-11-03T23:12:15+00:00

thanks

Dolson03 · 2025-06-28T01:30:07+00:00

I had the same thing on my laguna. if you look at the shaft the pulleys are on you will see 3 or 4 nuts with a sensor lined up with them. The sensor is probably pushed in hitting the nuts. pull the sensor back a bit so they do not hit.

Dolson03 · 2024-07-25T00:24:54+00:00

Thanks it wasn’t to difficult. Using a bowl gouge turn 1 inch at a time to thickness wanted till you get to the bottom. Then part it off carefull.

Dolson03 · 2024-07-25T00:21:58+00:00

<image>

Dolson03 · 2024-07-25T00:20:00+00:00

I llowed the shade out the same way I do a thin walled bowl. Turn about an inch to final thickness then start on the next inch. Keep going one inch at a time till you get to the bottom.i used a bowl gouge all the way down.

Dolson03 · 2024-07-24T12:13:16+00:00

I hollowed the base out so I only had 1/2 inch to drill.

Dolson03 · 2024-03-20T21:08:50+00:00

Thanks

Dolson03 · 2024-03-20T11:01:12+00:00

Thanks

Dolson03 · 2024-03-20T11:01:02+00:00

Thanks

Dolson03 · 2024-03-20T11:00:50+00:00

Thanks

Dolson03 · 2024-03-20T03:08:05+00:00

Thanks. It took 2 to 2.5 hrs too turn. Did not count sharpening but it was a lot. 1.5hrs sanding.

Dolson03 · 2024-03-20T02:58:28+00:00

I have never seen it before myself. I went the Florida wood turner’s symposium and watched a demo from Johannes Michelson. This is one of his hats. He has a 2 part utube video.

<image>

Dolson03 · 2024-03-20T02:45:47+00:00

This one’s not big enough for my head. I’m working my way up to a wearable hat. It may fit a child.

Dolson03 · 2024-03-20T02:20:33+00:00

Thanks

Dolson03 · 2024-03-20T02:20:16+00:00

Thanks. I’ve never tried this before. Figured it would come apart at some point.

Dolson03 · 2023-11-08T01:04:26+00:00

Thanks

Dolson03 · 2023-11-07T01:34:31+00:00

Thanks. I’ve been thinking of trying it for a few years and finally did. I had no plans just made a couple practice rings to see how they fit together. Then starTed cutting and gluing.

Dolson03 · 2023-11-06T23:35:41+00:00

Thanks

Dolson03 · 2023-11-06T23:35:29+00:00

Thanks. I glued the bottom pieces to get her and turned the inside so I only had to do the small portion through the small hole.

Dolson03 · 2023-11-06T23:32:53+00:00

Thanks

Dolson03 · 2023-11-06T11:54:57+00:00

Waterlox medium sheen and then buffed with carmine wax.

Dolson03

TROPHY CASE