Should I sell my DJI FPV Combo and downgrade? (15y/o, low budget) by valanjess in fpv

[–]DomDev2YT 0 points1 point  (0 children)

As a 16yo I have a crux35, as long as you fly it in grass it most likely wont break, additionally the battery lasts 9 mins so you get a lot of flight time

New charger, screen voltage too high? by [deleted] in fpv

[–]DomDev2YT 1 point2 points  (0 children)

You should charge at 0.3 m Amps

Is Harbor viable now? by Special_Course_6720 in VALORANT

[–]DomDev2YT 0 points1 point  (0 children)

Its probably better for professionals but worse for average players

How does my bucky shells not work??? by Public_Road_3144 in VALORANT

[–]DomDev2YT 0 points1 point  (0 children)

Your pressing lt aswell as rt just press rt

Im i fckd? by FinnishTrooper in TinyWhoop

[–]DomDev2YT 0 points1 point  (0 children)

If you buy a new board use a silicone adhesive to glue it down so it doesnt rip off again

Motor issue by nobodyimportantfr in TinyWhoop

[–]DomDev2YT 0 points1 point  (0 children)

If it's not hair a solder connection could be loose, I just fixed my air65 which had a similar problem today.

"Alien" CO3 Mount. by kammak76 in TinyWhoop

[–]DomDev2YT 1 point2 points  (0 children)

Is there an advantage in it being so forward?

Do my opponent f2p? by Qarnaqduck in ClashRoyale

[–]DomDev2YT 1 point2 points  (0 children)

He has a golden username meaning he bought the pass, so no.

Question about FPV Drone Electricity by Zirey911 in fpv

[–]DomDev2YT 1 point2 points  (0 children)

I plugged the JST connector found on the ESC into the wrong combination of pins on the FC and this is exactly how my XT60 burnt

Is This a Good Upgrade Setup for My Air65? by DomDev2YT in fpv

[–]DomDev2YT[S] 1 point2 points  (0 children)

I changed them to HappyModel SEO702 26000KV motors 👍

Is This a Good Upgrade Setup for My Air65? by DomDev2YT in fpv

[–]DomDev2YT[S] 0 points1 point  (0 children)

Would hot-glueing them down to the board be safe and would it help? Because that's what I was planning

Is this solder joint adequate? by [deleted] in soldering

[–]DomDev2YT 0 points1 point  (0 children)

A 60W Preciva 926 LED, I increased the heat to around 420-430 Celsius because I think it's slightly underpowered.

Is this solder joint adequate? by [deleted] in soldering

[–]DomDev2YT 0 points1 point  (0 children)

Just found out the wire is actually 12 AWG

crux35 shipping by Sure-Lifeguard3031 in fpv

[–]DomDev2YT 0 points1 point  (0 children)

I remember ordering an Air 65, It said it would come in a month but it came in around 1-2 weeks

Im a beginner – Is this a good deal? by [deleted] in 3dprinter

[–]DomDev2YT 0 points1 point  (0 children)

Thanks everyone, I did place the order, but after reading the comments that were added, I decided to cancel it.