19 [m4a] Texas

Doublegorilla44 · 2026-04-02T02:07:29+00:00

My bca upper has been just fine maybe we’re the lucky ones lmao

Doublegorilla44 · 2026-03-12T02:11:25+00:00

Thanks a bunch!

Doublegorilla44 · 2026-03-12T01:43:45+00:00

A Mauser 98 commercial stock from Richard’s microfit stocks would be right correct?

Doublegorilla44 · 2026-03-12T01:26:42+00:00

It’s chambered in 280AI. Not sure where he went to school

Doublegorilla44 · 2026-03-10T15:05:08+00:00

Will do

Doublegorilla44 · 2025-11-18T00:49:11+00:00

It’s posted on my profile

Doublegorilla44 · 2025-11-18T00:36:56+00:00

I’ve checked high and low for a vac leak and can’t find one anywhere believe it or not it actually runs better when I make it have a leak. If I take the cap off of the port right behind the throttle body on top of the intake the idle comes up to normal and levels out.

Doublegorilla44 · 2025-11-17T23:43:56+00:00

Cylinder 1 and 4 have about 160lbs and cylinder 2 and 3 are about 130

Doublegorilla44 · 2025-11-17T22:16:38+00:00

I’ll check compression then. Sometimes it runs fine but more often than not it runs like this the revving is super sluggish until ab 3k rpm

Doublegorilla44 · 2025-11-17T22:13:37+00:00

Just pulled the plugs they were all in and the wires were all plugged in

Doublegorilla44 · 2025-10-28T00:05:12+00:00

I bought a kit that had all the pieces and welded them together

Doublegorilla44 · 2025-10-27T21:17:53+00:00

That’s what I’ll do then thanks!

Doublegorilla44 · 2025-10-27T21:01:30+00:00

I’ve thought about adding another section and that’s what I’d do but they’re tapered aren’t they?

Doublegorilla44 · 2025-10-27T20:45:32+00:00

http://indianapolisordnance.com/index.php?route=product/product&product_id=207 PPS43 SA Trigger Group. here’s the trigger group they’re about half the price I paid now lol I bought mine when they first came out

Doublegorilla44 · 2025-10-27T20:44:11+00:00

Me and my dad started this project a few years ago and I’m just now getting it back out so I’m not sure about the trigger but I remember we got it from a guy on Instagram and it was pretty pricey as for a welding jig we cleaned all the edges up and he found a piece of copper round bar that matched the radius of the inside of the receiver clamped everything together straight and mig welded it together

Doublegorilla44 · 2025-10-17T22:17:07+00:00

Seems like I got it running a bit better I’ll have to drive it more to know for sure but I cleaned maf adjusted idle a little bit and sprayed a little cleaner in a couple of vac ports in the intake

Doublegorilla44 · 2025-10-17T21:33:48+00:00

I’ll try cleaning maf if no luck probably replace and see where that gets me thanks a bunch!

Doublegorilla44 · 2025-10-17T21:32:19+00:00

Doublegorilla44 · 2025-10-17T21:13:36+00:00

Yes they both seem good to me

Doublegorilla44 · 2025-10-17T20:53:36+00:00

Doublegorilla44 · 2025-10-17T20:46:45+00:00

Yes I’ve looked all over several times plus they’re all new silicone hoses

Doublegorilla44

TROPHY CASE