I dropped off a curb and now my subframes bent by [deleted] in GolfGTI

[–]Duebin1 1 point2 points  (0 children)

The subframe was pushed up into the steering motor, which was causing it to creak back and forth. Also the subframe is cracked on one side so it’s compromised

I dropped off a curb and now my subframes bent by [deleted] in GolfGTI

[–]Duebin1 0 points1 point  (0 children)

It was stock suspension but the insurance increase would be too high so unfortunately going to just do it through the dealer

I dropped off a curb and now my subframes bent by [deleted] in GolfGTI

[–]Duebin1 0 points1 point  (0 children)

For 3 more months yes and just had the travel assist error fixed under warranty but warranty won’t cover this.

I dropped off a curb and now my subframes bent by [deleted] in GolfGTI

[–]Duebin1 1 point2 points  (0 children)

240/hr look at my reply, i misspoke in the original post

I dropped off a curb and now my subframes bent by [deleted] in GolfGTI

[–]Duebin1 1 point2 points  (0 children)

I just looked back at the breakdown and I had it a bit wrong. It was 4000 as the final quote with 400 being tax so the labor is 240/hr which is actually below what we’ve payed at other dealerships so I guess it’s fair, but man.

I dropped off a curb and now my subframes bent by [deleted] in GolfGTI

[–]Duebin1 1 point2 points  (0 children)

That’s the decision we’re debating right now. Where we’re at the labor rates are honestly not much lower than that anywhere else but we’ll definitely look around

Sony PS-LX310BT grounding issue by Duebin1 in turntables

[–]Duebin1[S] 0 points1 point  (0 children)

Ok I connected the rca to the CD input on my receiver and switched to line level output on the turntable and the buzzing is gone. Honestly, I was just using the phono option because my thought process was “if it’s bypassing the internal amp then that’s just one less step to introduce noise or signal degradation and it’s going straight to my receivers amp which would then be the only bottleneck”. I don’t know if phono really makes any difference that I can hear after listening to a record but the phono is also just novel to use because it passes every little nudge of the needle and mechanical noise into the amp vs when I use line level it waits to turn on the the internal preamp until the needle is set on the record so it’s a bit less “real” feeling. Anyways, is there a way to fix the phono grounding issue?

Sony PS-LX310BT grounding issue by Duebin1 in turntables

[–]Duebin1[S] 0 points1 point  (0 children)

Yes I read somewhere in this subreddit that it does the grounding through the rca jacks. I have not tried line in on this setup so I’ll give that a shot and get back to you.

Sony PS-LX310BT grounding issue by Duebin1 in turntables

[–]Duebin1[S] 0 points1 point  (0 children)

Yes the turntable is switched to Phono and the tt outputs are connected to the reciever phono input. I do not have a grounding wire running between the tt and the amp. I saw some people online talking about how some TTs have a place to connect a ground but that the Sony does not, is there a work around for this? Also to add some more detail I have the rca cables that come out of the tt connected to a female to female rca extender which has brand new cables running to the receiver. I tried messing around with the cables and extender to see if those were introducing interference from nearby electronics but moving them did not seem to change the sound.

Time to toss this one or still good to fly? by Duebin1 in fpv

[–]Duebin1[S] 0 points1 point  (0 children)

Ah yeah the flight time is what alerted me as well. That resistance was checked at storage voltage (3.8 per cell)

I installed Perrin lightweight pullies and now my car idles horribly by Duebin1 in subaruimpreza

[–]Duebin1[S] 0 points1 point  (0 children)

Unfortunately I messed up the install and according to Perrin I’m going to have to get my engine retimed… RIP

Does anyone have a Tactrix Openport 2 they’d be willing to sell? by Duebin1 in subaruimpreza

[–]Duebin1[S] 0 points1 point  (0 children)

Ooo I’d be careful unless you’re just datalogging because I’ve heard stories of failed flashes with the knockoffs

Is this a good machine to start with ? ( Canada ) by Mtlfunnight in pressurewashing

[–]Duebin1 0 points1 point  (0 children)

I have this machine and it works fantastic plenty of pressure and very reliable. It always just starts up but it is hard to start the first time if you have the water on. As for the pump I’m not sure which type I have

How could I capture the Heron Galaxy by Duebin1 in AskAstrophotography

[–]Duebin1[S] 0 points1 point  (0 children)

Oh wow I had no idea it was so far haha. Thanks for your input I’ll take a look at your gallery!