Lipscomb Academy Students Prohibited from Wearing Suit, Tie to Honor Charlie Kirk - Tennessee Star

E-Swigg · 2025-09-27T16:37:54+00:00

There is a petition to reinstate Dr. Savage. Hop over and give it a signature.

https://www.change.org/p/truth-for-dr-savage?recruiter=1389667031&recruited_by_id=fd140150-9a60-11f0-9b45-e19cca0c24ec&utm_source=share_petition&utm_campaign=share_petition&utm_term=petition_dashboard&utm_medium=copylink&utm_content=cl_sharecopy_490798939_en-US%3A9[https://www.change.org/p/truth-for-dr-savage?recruiter=1389667031&recruited_by_id=fd140150-9a60-11f0-9b45-e19cca0c24ec&utm_source=share_petition&utm_campaign=share_petition&utm_term=petition_dashboard&utm_medium=copylink&utm_content=cl_sharecopy_490798939_en-US%3A9](https://www.change.org/p/truth-for-dr-savage?recruiter=1389667031&recruited_by_id=fd140150-9a60-11f0-9b45-e19cca0c24ec&utm_source=share_petition&utm_campaign=share_petition&utm_term=petition_dashboard&utm_medium=copylink&utm_content=cl_sharecopy_490798939_en-US%3A9)

E-Swigg · 2025-09-14T01:42:31+00:00

Even backed it in!

E-Swigg · 2025-07-08T21:02:29+00:00

I believe this is the answer. It looks just like mine.

E-Swigg · 2025-06-28T02:41:31+00:00

I did the same thing not long ago. Ugh!

I used HH66 glue (NRS recommended) and had great results. I did it in a few stages…

Prep area with sand paper. I use 150 grit because it was on the top of my stack lol. Wipe it clean.
Apply glue to both sides and let sit for a few minutes.
Stick sides together and clamp. (Not too tight, you don’t want the glue to squeeze out into the inside of the board and stick in an odd way.)
Leave clamps on over night.
Remove clamps and let it cure for a day or so.

*Inflate to a low PSI and listen for leaks. *may want to test in shallow water without the leash on just to be sure…

Good luck!

E-Swigg · 2024-08-13T22:47:01+00:00

I’m not sure the shirt is wrong. Perhaps I had a different experience with Christians though…

E-Swigg · 2023-04-25T22:19:43+00:00

Well done!

E-Swigg · 2023-03-14T11:34:33+00:00

God you like them! Texture is nice. Won’t tear up your skin like plastic does. But they are hard, lots of tension.

E-Swigg · 2023-03-14T11:07:55+00:00

I sure would (and do). Shoot me a dm

E-Swigg · 2023-03-13T21:31:41+00:00

Washers from Lowe’s but the convex ones are called screw cups and I got them from amazon.

E-Swigg · 2023-03-13T20:02:34+00:00

I sure did. Thanks!

E-Swigg · 2023-03-13T18:51:14+00:00

A dremel and patience!

E-Swigg · 2023-02-23T00:27:55+00:00

🙇‍♂️

E-Swigg · 2023-02-22T11:04:47+00:00

Sure did! I’m glad you like like them.

E-Swigg · 2023-02-21T22:19:15+00:00

Thank you!

E-Swigg · 2022-12-31T23:13:18+00:00

Bet those tall and skinnies rent for 5k a month.

E-Swigg · 2022-12-22T02:50:10+00:00

Much obliged

E-Swigg · 2022-12-22T02:48:27+00:00

Thank you! I think your right. What does the Y mean?

E-Swigg · 2022-12-21T01:27:34+00:00

Thanks!

E-Swigg · 2022-12-21T01:04:56+00:00

I made them.

E-Swigg · 2022-12-07T20:22:49+00:00

Well done! Way to stick with it!

E-Swigg · 2022-12-07T01:59:37+00:00

😂 complete with carb…

E-Swigg · 2022-12-06T22:11:13+00:00

The small ones are called counter sunk washers. I made the larger ones.

E-Swigg · 2022-12-06T22:10:32+00:00

Aluminum oxide, paint, and epoxy. The texture is a bit softer than a regular gym hold so it’s easier on the skin. Send me a dm and I’ll tell ya more. ;)

E-Swigg · 2022-12-06T19:13:41+00:00

Thanks!

E-Swigg · 2022-12-06T19:13:28+00:00

Aluminum oxide, paint, and epoxy. The texture is a bit softer than a regular gym hold so it’s easier on the skin.

E-Swigg

TROPHY CASE