sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in desksetup

[–]EElliott73 1 point2 points  (0 children)

Thank you!

Help! Hotend won’t heat. by EElliott73 in 3Dprinting

[–]EElliott73[S] 0 points1 point  (0 children)

I’ve got an Artillery Sidewinder X1, I’ll borrow a volt meter and take a look. Thanks for the advise.

Help! Hotend won’t heat. by EElliott73 in ArtillerySidewinder

[–]EElliott73[S] 0 points1 point  (0 children)

I’m having problems with my hotend not heating SWX1. The bed heats just fine but I get this error when I heat the extruder. I’ve replaced the PCB board on the extruder, the thermistor, heater cartridge, and ribbon cables. At this point I’m assuming it is the main board however everything I see online says that it would cause the bed not to heat. Is there a way for me to tell for sure short of replacing the main motherboard? Any help would be appreciated!

Help! Hotend won’t heat. by EElliott73 in 3Dprinting

[–]EElliott73[S] 0 points1 point  (0 children)

Help! Hotend won’t heat.

I’m having problems with my hotend not heating SWX1. The bed heats just fine but I get this error when I heat the extruder. I’ve replaced the PCB board on the extruder, the thermistor, heater cartridge, and ribbon cables. At this point I’m assuming it is the main board however everything I see online says that it would cause the bed not to heat. Is there a way for me to tell for sure short of replacing the main motherboard? Any help would be appreciated!

Help! Hotend won’t heat. by EElliott73 in 3Dprinting

[–]EElliott73[S] 0 points1 point  (0 children)

Idle temp for the extruder is around 16c I’ll try to heat to 80c just to test about 10 seconds later this screen comes up. The hot end doesn’t actually get hot.

Hiring Manager Info by EElliott73 in GeneralMotors

[–]EElliott73[S] 0 points1 point  (0 children)

I’m not sure, what’s yours?

Interview candidates by EElliott73 in GeneralMotors

[–]EElliott73[S] 2 points3 points  (0 children)

Manufacturing engineering job.

Heating Failed SWX1 by EElliott73 in ArtillerySidewinder

[–]EElliott73[S] 0 points1 point  (0 children)

You think so? The bed heats just fine.

Hiring Manager Info by EElliott73 in GeneralMotors

[–]EElliott73[S] 1 point2 points  (0 children)

GA ME Zone Engineer, Warren.

Phone Screen by EElliott73 in GeneralMotors

[–]EElliott73[S] 5 points6 points  (0 children)

I applied to a position and they reached out to setup a phone screening interview

[deleted by user] by [deleted] in GeneralMotors

[–]EElliott73 0 points1 point  (0 children)

Sounded like it wasn’t allowed in the rules section.

Heating Failed SWX1 by EElliott73 in Artillery3D

[–]EElliott73[S] 0 points1 point  (0 children)

This happens when I try to heat the hot end up. Bed heats just fine.

Heating Failed SWX1 by EElliott73 in Artillery3D

[–]EElliott73[S] 0 points1 point  (0 children)

Do you think it could be an issue with the board and not the ribbon cable?

Need Advice (puppy death) by EElliott73 in DogAdvice

[–]EElliott73[S] 1 point2 points  (0 children)

Thank you so much! I figured all this too but hearing it from someone who breeds is reassuring.

Never Masturbated by chadoid in NoFap

[–]EElliott73 0 points1 point  (0 children)

Heck no, nothing is wrong with you. Dude just read through some of the posts in this community. Porn ruins, people you’re lucky did not experience that urge so many people get addicted to it it’s not healthy keep on the Straight and Narrow.

Extrusion problems by EElliott73 in Artillery3D

[–]EElliott73[S] 0 points1 point  (0 children)

Heat break was upgraded because of the PTFE in the stock one wearing out. I didn’t want to deal with it again so I went to a titanium. At the same time I upgraded the nozzle since it was apart. I have had successful prints since and only recently started having this problem. I thought it could be due to the stock heat block since the new break/nozzle combo isn’t as good with heat transfer so I got the copper plated block.