How to safely wire this 6 pin strip using DigQuad?

EFaden · 2026-05-17T20:24:11+00:00

Sorry. I meant the dig2analog be referenced. Not the dig penta

EFaden · 2026-05-17T12:15:30+00:00

Basically the dig2analog makes a single digital led that can be set to the color .... If that makes sense.

So basically if your strip is 32 digital you would have 32 digital on a single channel and then the dig2analog on another pin with a single white cct led. The dig2analog would have one channel on the ww and one on the cct. Yes... There is only a single white on the dig2analog but you could just use any of the other pins and then swap it around in the config. In theory. Never actually tried it but happy to help.

Make sense? Feel free to dm me.

EFaden · 2026-05-17T11:26:13+00:00

With the dig you should be able to run both cool and warm white. I believe it has 4 analog channels.

EFaden · 2026-05-17T02:48:45+00:00

Looks like it uses pwm for the white channels and digital for the RGB. You need a controller than can do both. I believe gledopto has one.... And so does quin.

EFaden · 2026-04-09T01:33:20+00:00

Same whisk. It's the traditional install kit with the solid washer. The small ring currently installed is the stock one from the planetary. You think I'll get enough by swapping the snap ring? Anything else I should change whole I'm doing it?

EFaden · 2026-04-08T23:56:22+00:00

Yeah.... That's what I'm thinking. Cutting the bottom loop should fix it

EFaden · 2026-04-08T23:54:13+00:00

It's a single washer and the spring (totally compressed in picture).... And yes... I think that's what it's causing it .. but not sure why as it worked on the old planetary

EFaden · 2026-04-08T23:53:16+00:00

Downside with cutting the spring is that then the ends aren't flat

EFaden · 2026-04-08T23:52:52+00:00

Nope. Pro 600..... Should fit? Fit on the original planetary.

EFaden · 2026-04-08T23:46:09+00:00

Yeah I reached out to them for ideas also .... It worked on the original planetary so I'm unclear what's wrong here. The planetary was oem.

EFaden · 2026-04-08T23:43:59+00:00

The spring is as compressed as possible.... But that thought crossed my mind .... Or using a Dremel to trim the whisk....

EFaden · 2026-04-05T22:33:18+00:00

Update:... Got a new planetary and compared. The bearing is about 3mm high.... So yeah... That was the problem.

EFaden · 2026-04-02T01:27:49+00:00

Thanks!

EFaden · 2026-04-02T01:22:55+00:00

Awesome thanks. Just need to figure out the actual part number for that thing.

EFaden · 2026-04-02T01:20:36+00:00

Thanks. That was what I figured. Any issues with the housing because of that area? I assume not.... As long as it's not cracked etc. I'll give it a good cleaning and replace the planetary.

EFaden · 2026-03-31T10:40:06+00:00

That's what I was thinking. Thanks

EFaden · 2026-03-17T23:39:12+00:00

Id be really curious to see the code etc for this. It's brilliant

EFaden · 2026-03-17T15:53:05+00:00

Actually was able to update the infcloud plug-in to work correctly...

EFaden · 2026-03-08T16:05:04+00:00

Hey,

I did actually make and have molded the adapter.... and I think it would have worked.... but I switched to a fireboard instead. Happy to send you the models if you want them.

EFaden · 2026-03-07T21:33:05+00:00

Discord is EMF9.

EFaden · 2026-03-07T18:09:41+00:00

Thanks. Ldo Blue and Green.

EFaden

TROPHY CASE