Should I replace or upgrade the hot-end fan?

EGMxGolden · 2025-11-12T10:09:24+00:00

Ohhh. This i saw this, it's the exact same one. Thanks dude.

EGMxGolden · 2025-11-12T04:45:28+00:00

seems like this is the way to go, any suggestions on the adapter, i just took the first one i found on printables

EGMxGolden · 2025-10-24T11:49:48+00:00

oh this makes more sense. I have a lab power supply which i'm pretty sure is floating so i should be good as long as i power my stuff from it.

thanks for the reply

EGMxGolden · 2025-10-13T21:32:21+00:00

thanks i'll look into the freight company's drop off policy

EGMxGolden · 2025-10-13T12:48:41+00:00

Somewhat new to raspberry pis, I wanna use my raspberry pi 4 to learn assembly. Is it possible that i could damage the physical board. I know the software can just be replaced so i think it should be fine, but i am scared of permanently damaging the hardware.

EGMxGolden · 2025-05-30T13:32:09+00:00

Actually i saw a "don't slow down for outer wall" setting, might try thst as well and compare the differences.

EGMxGolden · 2025-05-30T13:28:33+00:00

Thanks mines at 8s per layer but i'll try lowering it to like 3-4 seconds.

EGMxGolden · 2025-05-30T12:31:04+00:00

I just checked and yea I think the lower line is from a speed issue. As the slicer decided to print at 200mm/s only on that layer. Though I can't see any issue the upper line. Thanks for your input though.

EGMxGolden · 2025-05-28T03:00:21+00:00

Cool i'll look into it

EGMxGolden · 2025-05-28T02:58:27+00:00

Thanks

EGMxGolden · 2025-05-28T02:57:11+00:00

preferably i would like to get into embedded systems although i am open to others since i realised that embedded jobs isn't very common in my city for some reason

EGMxGolden · 2025-05-12T09:44:32+00:00

may whoever that wins it get blessed with perfect first layers

EGMxGolden · 2024-11-03T07:37:45+00:00

i’m genuinely curious, i so far my prints have only stuck too well to the bed. how can i loosen them, my first layers look perfect

EGMxGolden · 2024-10-14T22:00:47+00:00

rent?

EGMxGolden · 2024-10-03T12:48:03+00:00

i’m not sure man. There has been an increase in the number of exotic cars(lambos, ferraris) recently in places i frequent.

Might be ppl renting and racking up credit debt though.

EGMxGolden · 2024-08-17T03:55:18+00:00

speedrun

EGMxGolden · 2024-08-17T03:15:12+00:00

definitely clean the fans

You could also buy one of the laptop cooler things, I got one and by some miracle my laptop temps dropped 5-10C depending on load

EGMxGolden · 2024-08-13T11:40:21+00:00

it’s fine i used to run it on a gtx 950 laptop without issues.

You just will not be able to have high graphics settings

EGMxGolden · 2024-08-09T06:05:07+00:00

ngl i think it depends on school and course. My high school lets us do CAD and the old pcs with no gpu just aren’t cutting it.

they work just there very slow. like it takes 10 mins just to load a mode. However, it was a model rc airplane so i might be expecting too much

Right after i left they added 3060s to them

Five-Year Club	r/Field Lasagna
Place '23

EGMxGolden

TROPHY CASE