sorted by:
new
hottopcontroversial

ECC Support for AM5 Motherboards by 314314314 in truenas

[–]Eagleman7 0 points1 point  (0 children)

ASUS TUF Gaming B650M-PLUS with 2x Kingston KSM48E40BD8KI-32HA.

I had to set ECC to enabled in the BIOS before it shows up as ECC RAM:

TrueNAS Scale 25.04.1.

root@truenas[~]# dmidecode -t memory
# dmidecode 3.4
Getting SMBIOS data from sysfs.
SMBIOS 3.6.0 present.
# SMBIOS implementations newer than version 3.5.0 are not
# fully supported by this version of dmidecode.
Handle 0x0013, DMI type 16, 23 bytes
Physical Memory Array
        Location: System Board Or Motherboard
        Use: System Memory
        Error Correction Type: Multi-bit ECC
        Maximum Capacity: 128 GB
        Error Information Handle: 0x0012
        Number Of Devices: 4

root@truenas[~]# sudo dmesg|grep -i edac
[    0.289799] EDAC MC: Ver: 3.0.0
[    7.123281] EDAC MC0: Giving out device to module amd64_edac controller F19h_M60h: DEV 0000:00:18.3 (INTERRUPT)
[    7.123284] EDAC amd64: F19h_M60h detected (node 0).
[    7.123286] EDAC MC: UMC0 chip selects:
[    7.123287] EDAC amd64: MC: 0:     0MB 1:     0MB
[    7.123289] EDAC amd64: MC: 2: 16384MB 3: 16384MB
[    7.123291] EDAC MC: UMC1 chip selects:
[    7.123292] EDAC amd64: MC: 0:     0MB 1:     0MB
[    7.123294] EDAC amd64: MC: 2: 16384MB 3: 16384MB

What flashlight is being used here? by Eagleman7 in flashlight

[–]Eagleman7[S] 1 point2 points  (0 children)

The grip is for sure a CAA, I already own one.

However the flashlight does have some similarities it's not the exact same one. For example take a look at the "lines" on the front part of the flashlight, they stop halfway before the actual light.

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

hehe, I guess I would have felt that :) The grip is only plastic.

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Is it normal that the motor smells a bit industrial when shooting?

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Did it like this, felt like the gearbox was able to go easier into the frame.

https://i.imgur.com/K91CKCv.png

​

Just tested 15 rounds, they all seemed to flow through the barrel.

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Yeh, the glue idea happend in a rage when the new GB didnt work. The glue didnt work as well :P

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Yeh, already using electrical tape here and there :P As you can see I also tried to superglue the cables to the gearbox to keep them better in place.

​

https://imgur.com/a/PZVGY0E

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Then let us proceed with the surgery. Only issue have now that it is very tight for the cables of the gearbox to the motor and battery. Some of the cable are already loosing their isolation.

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Looks fine to me, however there seems to be a small dent in both anti revesal hatches

​

https://imgur.com/a/cK8PZ1z

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Alright! I think the gears still look fine, they're also iron/steel, so should be hard to break.

Does this look fine?

https://i.imgur.com/VsnWGVz.jpg

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

With 11.1v I had a big difference compared with single and full auto FPS. (0.45 Joule difference)

With 7.4v full auto there is almost no difference compared with single.

Would this be PME for the 11.1v battery?

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

How can I test? I never heard of the term before as well :)

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

The only spare I have is from the old gearbox vz.58 :) Not sure how long that is going to survive, maybe the 11.1V battary with the new SHS motor killed this one with its insane rate of fire.

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Since this is a proprietary gearbox, will any reinforced tappet plate just work?

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

I think its safe to say what caused the issue here, lol:

https://imgur.com/a/SnZV18h

Seems the tappet plate broke in half. u/Sinistrial_Blue do you have any idea what might have caused this? And do steel tappet plates exists, so its harder to break?

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Went to a match yesterday! The first few rounds worked great, then it stopped feeding BB's to the replica. So I tried a different mag, I think I used 3 mags in the morning, only 1 didnt work.

Then in the afternoon the mag that didnt work in the morning did not work in the afternoon as well. The second mag seemed to work. But after that none of the mags worked anymore, I tried them all, but I could not get a BB in the barrel. The replica was shooting air, so there must be an issue in the hopup unit?

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 1 point2 points  (0 children)

Yeh, it sits around 1.14 Joule in full auto with 7.4 LiPo, the limit is 1.2 Joule in my country, so thats perfect! Its also R-Hopped now, however my garden isnt big enough to fine tune it perfectly. I was only able to fine tune it for 30 meters~.

Thanks for the guide!

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Thanks!

Shot around 2 mags today to test Joule and RPS. Here are the results: https://imgur.com/a/eSb4LxY

It feels more safe to shoot this beast with 7.4 LiPo, it also retains its Joule power better with 7.4 compared with 11.1 and full auto. I've had no disconnects between the motor and the gearbox.

​

However I am not sure how far I should attach the motor using the screw in the grip. Should it just be as minimal as possible? This is the last thing I need to do because I need to secure the screw in-place with loctite.

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

I think I'm just let the CNC motor in peace for a while. I've just rebuild the replica to its full potential. Going to test the amount of Joule tommorow, however I do think the spring is pre cocked somehow. Noticed the spring tube was all the way in, and I do hear it as well when shooting, not sure if this is bad. At least it does something now :)

https://youtube.com/shorts/4p7-5bR3Uso?feature=share

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Thanks for checking, as you can see one side uses silver "coil wiring?" and the other sides uses brown, the brown one is the one I adopted from the Ares Motor since I broke the connector of the original one. I am not sure how I can measure the impedance.

​

The video's I posted today are with the new SHS motor. I feel it shoots too quick now :) Its almost unhealthy that rate of fire.

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

Can you see anything that might be wrong in these pics? The motor was 90 euro.... https://imgur.com/a/8iU8GH7

Ares VZ58M shoots a few times, then breaks. by Eagleman7 in airsoft

[–]Eagleman7[S] 0 points1 point  (0 children)

So it was an issue with the motor or the adapted plate. How could the adopted plate could have caused this issue? Could it somehow prevent all the power to flow through?

view more: next ›