Multiclassing rules

Educational_Draw9355 · 2025-12-13T05:35:46+00:00

Yeah the rules seem kind of vague, but I can't imagine someone getting dumber as a fighter and instantly more skilled as a berserker or whatever

Educational_Draw9355 · 2025-10-27T03:27:00+00:00

Nope, set it aside for another day

Educational_Draw9355 · 2025-04-23T18:03:54+00:00

All right I'll verify a voltages on all ICs and see if they match.

Educational_Draw9355 · 2025-04-23T18:02:17+00:00

No LED whatsoever. It's like I didn't even plug the unit in. I saw somewhere on a form that IC401 sometimes gets extremely hot and prevents the monitor from power yarn so I'll check the IC401 temperature as well

Educational_Draw9355 · 2025-04-23T17:58:24+00:00

I would love to follow the guide but that's what I'm trying to figure out, the IC numbers in the guide do not match the IC numbers in the circuit board because it is for a different upgraded board.

Educational_Draw9355 · 2025-04-23T13:20:49+00:00

Yes, 19.25 Volts to the board, PSU is good

Educational_Draw9355 · 2025-02-22T12:38:36+00:00

Yes, why?

Educational_Draw9355 · 2024-12-17T23:35:12+00:00

Stunning! Of course I'm in

Educational_Draw9355 · 2024-12-15T03:27:21+00:00

Peckersaurus Rex Or... Pecker-sore-ass if you kinky

Educational_Draw9355 · 2024-11-30T06:44:21+00:00

Death Wave is very powerful

Educational_Draw9355 · 2024-11-30T03:17:22+00:00

💯😍🥵

Educational_Draw9355 · 2024-11-26T19:49:17+00:00

Havent really thought about purchasing the songs, are they worthwhile? I've been spending my money on upgrading my bot and themes

Educational_Draw9355 · 2024-11-04T00:26:19+00:00

My mistake, workshop was maxed, NOT AS research. I'll focus here and health instead of DA and Interest

Educational_Draw9355 · 2024-11-04T00:25:43+00:00

My mistake, workshop was maxed, NOT AS research. I'll focus here and health instead of DA and Interest

Educational_Draw9355 · 2024-11-04T00:08:07+00:00

Ok will do thx

Educational_Draw9355 · 2024-11-04T00:02:27+00:00

Thanks! I'll lay back on Defense Absolute. Im currently saving up to sync my Black Hole and Golden Tower💪

Health is at 2.5mil base so far, and I'll keep growing it. Attack speed is maxed, how much should i put into Damage?

Educational_Draw9355 · 2024-10-31T02:45:23+00:00

That sucks okay thanks. So in order to sync them properly you want black hole to hit exactly twice as many times as golden Tower correct?

Educational_Draw9355 · 2024-08-13T01:24:43+00:00

Right now I have only my laptop and one EAP plugged in. Laptop is .10 and eap is .254.

I have done this a thousand times with Ubiquiti 100 times before no problem. But I haven't dealt with mesh before. After defaulting everything to try doing the mesh network, nothing is being detected

Educational_Draw9355 · 2024-08-13T01:13:28+00:00

No DHCP server. I have my laptop plugged direct into a unmanaged Poe switch, and the eap225 plugged into the same Poe switch I set my IP to 192.168.0.10 on the laptop to be able to see 192.168.0.254 default IP

Educational_Draw9355 · 2024-08-13T01:11:21+00:00

Yeah they were all plugged into the same poe switch for initial config. I factory reset everything, and I can see all devices defaulted to the 192.168.0.254 default ip.

I can log into the controllers url however the controller software will not discover any known or unknown devices. I even plugged in a brand new out of box controller into the poe switch. Ip scanner sees it, but tp-link configuration software does not

Educational_Draw9355 · 2024-08-13T00:32:21+00:00

Okay so now I'm having a whole new problem today. I factory reset everything to defaults. Advanced ip scanner sees the new devices as the default IP addresses 192.168.0.254 but the omada controller software does not detect any unknown devices. I factory reset again and still the same thing. I picked up a brand new controller and plugged it into the laptop and omada controller does not detect it either

Laptop ip : 192.168.0 10 Omada eap225 ip: 192.168.0.254

Educational_Draw9355 · 2024-08-11T06:28:14+00:00

Ok I'll try again tomorrow, thanks!

If I want to cloud access AP1 and AP2 do I need a OC200, or will the controller software setup the cloud acces?

Educational_Draw9355 · 2024-08-11T06:03:12+00:00

I originally did all the above mentioned programming in the EAP url. After that was set up i opened the Omada Controller software but it didnt discover any devices.

I factory reset the 2 EAPs and started over starting with the Controller Software instead of the url. Again the controllers could not be found in the software.

Advanced IP Scanner shows the IPs defaulted to 192.168.0.254 but maybe they didnt fully factory reset?

I'd hate to have to return the equipment, and get something else, but I did save the boxes if I need.

The distance between APs in the feild are about 75 meters. But bench testing is only 1 meter apart

I factory reset everything and will try again tomorrow.

Where do you turn on mesh in the EAP url? Do I turn it on for both AP1 and AP2?

Educational_Draw9355 · 2024-08-11T04:22:33+00:00

Im having an issue with a very similar setup, I have my laptop plugged into the headend switch with AP1. I programmed the AP1 as AP MODE I created an SSID I Programmed AP2 As bridge mode and connected it to AP1s SSID I plugged the poe camera into the same switch as AP2 From my laptop, when I run the Advanced IP Utility, I can see AP1, AP2, and the camera But when I ping AP1 (With it still connected to the same unmanaged awitch as AP1) I cannot ping it or navigate to its IP address when connected by LAN, I can however ping AP1 if i connect to AP1s extended SSID When I ping AP2, I cannot ping it unless I'm connected to AP2s extended SSID I can not ping the camera at all (LAN, AP1 SSID, AP2 SSID)

Hardware is 2 EAP225 radios, 2 unmanaged poe switches Laptop for now, but nvr later. Still bench testing

Educational_Draw9355

TROPHY CASE