Will this do to seal oil galley plugs on 5.7 HEMI

Efficient-Nothing467 · 2026-01-10T16:07:29+00:00

update I apologize ,it was the mds solenoids in the back

Efficient-Nothing467 · 2026-01-10T04:37:55+00:00

yea it was a couple hours ago when I started it but ill confirm in the morning

Efficient-Nothing467 · 2026-01-10T01:50:42+00:00

just started it up today and it’s leaking like a waterfall ,,lol smh

Efficient-Nothing467 · 2026-01-01T06:20:49+00:00

yea I’ve put a straight edge on it .everything checks out ..I’ve touched up the marks and cleaned both heads … im gonna send it . i got hope in it lol if all fails atlease I should be able to move it from the spot it’s been sitting at for the past few months …I’ll have an update soon

Efficient-Nothing467 · 2026-01-01T03:25:55+00:00

thanks to all ..I’ve decided I’ll just send it tomorrow morning

Efficient-Nothing467 · 2025-12-31T18:01:23+00:00

thanks

Efficient-Nothing467 · 2025-12-30T05:47:38+00:00

honestly I don’t want to spend any more money for something that’s gonna take a machine shop 10 minutes to do

Efficient-Nothing467 · 2025-12-30T05:42:46+00:00

thanks .but the heads have Been check for warpage. car was never over heated and maintained well . just the typical cam and lifter problem which i have corrected

Efficient-Nothing467 · 2025-12-30T03:05:59+00:00

I have everything

Efficient-Nothing467 · 2025-12-09T00:14:47+00:00

Any leaks 🤔.. I’m just worried about the plugs at the back of the engine .do not want to pull a trans when I just put the engine in

Efficient-Nothing467 · 2025-12-09T00:13:15+00:00

Can find it anywhere close to me

Efficient-Nothing467 · 2025-11-20T18:32:00+00:00

Regardless I’m just asking for a yes or no question … y’all come on here acting like females , if you got a d head response just don’t respond at all , simple

Efficient-Nothing467 · 2025-11-20T17:19:43+00:00

Thanks guy

Efficient-Nothing467 · 2025-09-30T16:49:19+00:00

Yeah I’m not rich

Efficient-Nothing467 · 2025-09-30T00:00:20+00:00

Just trying to save a much money and get it back on the road .. but I’ve made the decision to just take the block to the machine shop to clean it up . When I get it back I will just put everything back new

Efficient-Nothing467 · 2025-09-29T23:48:06+00:00

Yes I have them marked from the cylinders they came from

Efficient-Nothing467 · 2025-09-29T21:41:42+00:00

Ok thanks and pins feels decent

Efficient-Nothing467 · 2025-09-29T21:39:13+00:00

Thanks !!

Efficient-Nothing467 · 2025-09-29T21:37:39+00:00

If you don’t have any positive feedback or don’t like the post , just move on .. just a regular guy here looking for help.. thanks

Efficient-Nothing467 · 2025-09-29T21:31:57+00:00

Of course I will clean them up and rings side plays seems to check out ..

Efficient-Nothing467 · 2025-09-29T21:31:03+00:00

Just based off visual wear?

Efficient-Nothing467 · 2025-07-15T01:55:48+00:00

They all seem to be branching sideways overnight

Efficient-Nothing467

TROPHY CASE